Back
[00:00:04] <zeeshan> but chips packed under it and pushed it up
[00:00:04] <_methods> drills pull up
[00:00:08] <_methods> relentlessly
[00:00:16] <_methods> especially when you don't want them to
[00:00:43] <zeeshan> i was feeding a bit hard too
[00:01:01] <zeeshan> they say you could do 0.006 ipr with a 3/16 drill bit
[00:01:04] -!- josue_mrkrin has quit [Remote host closed the connection]
[00:02:31] <XXCoder> whoops
[00:02:35] <_methods> especially when the drill "punches" through
[00:02:40] <Tecan> zeeshan nice rig, glad to see no bits were harmed in the making of that video
[00:02:42] <XXCoder> nice part at end though
[00:03:09] <ASRock_pc> zeeshan, you just had one clamp on it?
[00:03:11] <_methods> you can see it in action real easy on a piece of sheet metal
[00:03:28] <zeeshan> ASRock_pc: yea
[00:03:30] <zeeshan> was being lazy
[00:03:41] <_methods> lazy people have less fingers
[00:03:49] <ASRock_pc> i have all 9
[00:03:55] <XXCoder> and more scrap
[00:03:55] <_methods> hehe
[00:03:56] <ASRock_pc> err...
[00:04:33] <ASRock_pc> did you leave a skin cut and pop it out?
[00:05:51] <ASRock_pc> you're lucky that clamp didn't pop off
[00:05:57] <zeeshan> its only drilling
[00:06:01] <zeeshan> who cares
[00:06:07] <ASRock_pc> your fingers?
[00:06:08] -!- messine has quit [Ping timeout: 246 seconds]
[00:06:17] <zeeshan> where do you see my fingers near the machine
[00:06:22] <zeeshan> im like 5 feet away
[00:07:20] <ASRock_pc> do you wait on spindle.at.speed before feed moves?
[00:07:25] <zeeshan> yea
[00:07:55] <zeeshan> it stops the tool from plunging in at a weird speed
[00:08:12] <ASRock_pc> yep
[00:08:40] <zeeshan> i really love the chip break cycle
[00:09:01] -!- bobo_ [bobo_!63283ad9@gateway/web/freenode/ip.99.40.58.217] has joined #linuxcnc
[00:09:44] <ASRock_pc> how friggin deep did you drill that?
[00:10:08] <zeeshan> i forget but i think 1.5"
[00:10:13] <ASRock_pc> looks like about a foot deeper than you needed
[00:10:15] <zeeshan> i was trying to drill the plate below it
[00:10:24] <zeeshan> so i could pass a bolt through it
[00:10:24] <ASRock_pc> success!
[00:11:05] -!- Loetmichel [Loetmichel!~cylly@p54B10546.dip0.t-ipconnect.de] has joined #linuxcnc
[00:11:21] <zeeshan> i think ill use the peck cycle if the holes are like 3" deep
[00:11:33] <zeeshan> the chip break cycle seems to evacuate chips pretty good
[00:11:39] -!- JohnyK has quit [Ping timeout: 250 seconds]
[00:11:45] <ASRock_pc> yeah
[00:11:48] <_methods> yeah unless you have through spindle coolant that would be a good idea lol
[00:11:57] -!- Camaban has quit [Quit: Leaving]
[00:12:20] <zeeshan> if i get a part in the future that needs like a 3" hole, ill try chip break with delta 0.001 and retract 0.001
[00:12:25] -!- Loetmichel2 has quit [Ping timeout: 264 seconds]
[00:12:25] <zeeshan> and see how that works out
[00:12:38] <ASRock_pc> so did you make another or salvage that hole?
[00:12:45] <zeeshan> hole was fine
[00:12:47] <zeeshan> its just a clearance hole
[00:13:04] <zeeshan> the side of dril bits dont cut that well :)
[00:13:39] <ASRock_pc> i'm trying to decide if i like this pc
[00:13:57] <zeeshan> is that you tom
[00:13:58] <zeeshan> lol
[00:14:03] <ASRock_pc> yep
[00:14:12] <zeeshan> which asrock
[00:14:20] <ASRock_pc> Q1900m iirc
[00:14:28] <ASRock_pc> pro3
[00:14:30] -!- asdfasd has quit [Ping timeout: 252 seconds]
[00:14:32] <zeeshan> nice!
[00:14:52] <ASRock_pc> i put win7 32 on a hdd to load all my old junk
[00:14:58] <ASRock_pc> 64 wouldn't load anything
[00:15:17] <ASRock_pc> i may get the itx ver for lcnc
[00:16:21] -!- phantoneD [phantoneD!destroy@a89-152-21-144.cpe.netcabo.pt] has joined #linuxcnc
[00:17:45] -!- tjtr33 [tjtr33!~tjtr33@d47-69-239-176.try.wideopenwest.com] has joined #linuxcnc
[00:17:56] <zeeshan> i need a new mobo for the mill
[00:18:06] <ASRock_pc> these are cheap
[00:18:47] <ASRock_pc> won't run xp though
[00:18:53] <ASRock_pc> 7 or above
[00:18:54] <XXCoder> any of you has experence with TB6560
[00:19:04] <ASRock_pc> it's a stepper driver right?
[00:19:14] <XXCoder> its controller
[00:19:35] <XXCoder> but I cant find enough info on it on what spidle it would accept so on
[00:20:34] -!- phantoxeD has quit [Ping timeout: 272 seconds]
[00:21:27] <ASRock_pc> spindle?
[00:21:37] <ASRock_pc> looks like a stepper only driver board
[00:26:35] <XXCoder> some sites say the first 3 is "relay"
[00:26:48] <XXCoder> and some use it on spidle
[00:26:49] <ASRock_pc> what board?
[00:26:58] <XXCoder> a sec
[00:27:00] <ASRock_pc> or is it just the chip
[00:28:19] <XXCoder> https://dc244.4shared.com/img/BW1MQv0i/s7/0.8675843564667969/HPIM5996__4_.jpg
[00:28:53] <ASRock_pc> yep, looks like the one i clicked on ebay
[00:28:55] <XXCoder> oh yeah driver
[00:29:42] <ASRock_pc> it's probably a low current driver
[00:30:00] <ASRock_pc> 2-3A i'd guess
[00:30:06] <XXCoder> yeah it seemed unlikely it would be able to drive spidle
[00:30:08] <_methods> http://i00.i.aliimg.com/wsphoto/v0/847532296_1/JP-3136B-stepper-motor-driver-TB6560-3-axis-for-CNC-engraving-machine-with-0-10V-spindle.jpg
[00:30:35] <_methods> it just has an open I/O for spindle signal
[00:30:43] <_methods> pwm
[00:30:59] <ASRock_pc> so you need another driver for the spindle
[00:31:04] <_methods> yeah
[00:31:07] <XXCoder> ahh
[00:31:16] <ASRock_pc> it just gives you the control signal
[00:31:17] -!- f1oat3 has quit [Ping timeout: 248 seconds]
[00:31:17] <XXCoder> sp relay drives spidle driver?
[00:31:31] <ASRock_pc> maybe enable
[00:31:32] <_methods> or pwm to vfd
[00:31:33] <ASRock_pc> i dunno
[00:32:30] <XXCoder> http://www.aliexpress.com/item/Powerful-400W-CNC-12000RPM-Brushless-Air-cooled-DC-Spindle-Motor-with-Driver-High-speed-Long-life/32251014873.html
[00:32:34] <XXCoder> something like this?
[00:33:20] <XXCoder> http://www.aliexpress.com/item/xxx/2027895792.html probably compitable with my cnc frame
[00:33:21] <_methods> yeah but for that motor i don't know if you necessarily need taht driver
[00:33:45] <_methods> oh nm with that motor looks like you might need that
[00:34:55] <ASRock_pc> ok time to move some junk around
[00:34:58] -!- ASRock_pc has quit [Quit: Leaving]
[00:35:01] <_methods> http://www.georgegardner.info/software/tb6560-ebay-3-axis-driver-and-linuxcnc-emc.html/comment-page-1
[00:43:50] Jymmm is now known as Red70sShow
[00:43:55] Red70sShow is now known as Jymmm
[00:49:14] -!- arekm_ has quit [Read error: Connection reset by peer]
[00:49:42] -!- arekm [arekm!~arekm@ixion.pld-linux.org] has joined #linuxcnc
[00:49:42] -!- arekm has quit [Changing host]
[00:49:42] -!- arekm [arekm!~arekm@pld-linux/arekm] has joined #linuxcnc
[00:58:04] -!- Servos4ever has quit [Quit: ChatZilla 0.9.91.1 [SeaMonkey 2.26.1/20140612173529]]
[00:59:41] -!- ASRock_pc [ASRock_pc!~Tom@ip68-102-196-57.ks.ok.cox.net] has joined #linuxcnc
[00:59:58] -!- ASRock_pc has quit [Client Quit]
[01:00:13] -!- Tom_L [Tom_L!~Tom@unaffiliated/toml/x-013812] has joined #linuxcnc
[01:10:29] -!- toner [toner!~ink@c-73-189-30-247.hsd1.ca.comcast.net] has joined #linuxcnc
[01:11:27] -!- Tom_shop [Tom_shop!~Tl@unaffiliated/toml/x-013812] has joined #linuxcnc
[01:11:34] -!- Tom_shop has quit [Client Quit]
[01:12:01] -!- sumpfralle has quit [Ping timeout: 264 seconds]
[01:17:13] -!- messine has quit [Ping timeout: 264 seconds]
[01:19:24] -!- rob_h has quit [Ping timeout: 252 seconds]
[01:22:16] -!- sumpfralle [sumpfralle!~lars@subaru.opennet-initiative.de] has joined #linuxcnc
[01:24:53] -!- FreezingCold has quit [Ping timeout: 246 seconds]
[01:25:22] -!- jameshyde [jameshyde!cdb2569e@gateway/web/freenode/ip.205.178.86.158] has joined #linuxcnc
[01:25:23] -!- mozmck has quit [Read error: Connection reset by peer]
[01:25:50] -!- jameshyde [jameshyde!cdb2569e@gateway/web/freenode/ip.205.178.86.158] has parted #linuxcnc
[01:26:27] -!- mozmck [mozmck!~moses@67.210.159.245] has joined #linuxcnc
[01:45:41] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[01:52:37] -!- sumpfralle has quit [Ping timeout: 250 seconds]
[01:56:02] -!- Albright has quit [Quit: Albright]
[01:59:52] -!- Roguish has quit [Quit: ChatZilla 0.9.91.1 [Firefox 36.0.4/20150320202338]]
[02:15:23] -!- jerryitt has quit [Quit: Connection closed for inactivity]
[02:18:30] -!- teepee has quit [Ping timeout: 276 seconds]
[02:18:34] teepee_ is now known as teepee
[02:19:37] -!- karavanjo has quit [Ping timeout: 255 seconds]
[02:20:25] -!- Tom_L has quit [Quit: Leaving]
[02:33:31] -!- cnc1 has quit [Quit: ChatZilla 0.9.91.1 [Firefox 35.0.1/20150122214805]]
[03:19:55] <Tecan> http://blog.huntgang.com/wp-content/uploads/2014/06/arduino-tcrt5000-1024x507.jpg someone has an imagination :)
[03:20:09] <XXCoder> lol
[03:20:17] <XXCoder> its beter as that spy probe than at at
[03:20:42] <Tecan> just an ir sensor
[03:21:02] <Tecan> going to try attpempting free space optics for data communication
[03:21:30] <Tecan> this one will only be for short distance , not even sure it'll work
[03:22:01] <XXCoder> good luck :)
[03:22:27] <Tecan> thanks
[03:22:49] -!- _rob [_rob!~rob@host86-134-239-67.range86-134.btcentralplus.com] has joined #linuxcnc
[03:23:45] -!- __rob has quit [Ping timeout: 244 seconds]
[03:25:01] -!- AR_ has quit [Ping timeout: 264 seconds]
[03:34:29] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[03:42:21] -!- tjtr33 has quit [Quit: Leaving]
[04:00:26] -!- furrywolf has quit [Ping timeout: 244 seconds]
[04:02:30] -!- crazy_imp has quit [Ping timeout: 244 seconds]
[04:04:19] -!- crazy_imp [crazy_imp!~mj@a89-182-48-154.net-htp.de] has joined #linuxcnc
[04:04:19] -!- crazy_imp has quit [Changing host]
[04:04:19] -!- crazy_imp [crazy_imp!~mj@unaffiliated/crazy-imp/x-8704303] has joined #linuxcnc
[04:09:14] -!- micges has quit [Ping timeout: 265 seconds]
[04:16:23] -!- tjtr33 has quit [Quit: Leaving]
[04:18:12] -!- mhaberler [mhaberler!~mhaberler@193.228.47.221] has joined #linuxcnc
[04:45:15] -!- danylevskyi_ has quit [Quit: Leaving]
[04:52:53] -!- bobo_ has quit [Quit: Page closed]
[05:06:52] -!- ve7it has quit [Remote host closed the connection]
[05:23:25] -!- per_sonne_ has quit [Ping timeout: 264 seconds]
[05:44:37] -!- FinboySlick has quit [Quit: Leaving.]
[05:55:23] -!- jerryitt has quit [Quit: Connection closed for inactivity]
[06:04:53] -!- kwallace has quit [Ping timeout: 252 seconds]
[06:12:31] -!- nofxx_ [nofxx_!~nofxx@unaffiliated/nofxx] has joined #linuxcnc
[06:15:25] -!- nofxx has quit [Ping timeout: 264 seconds]
[06:18:54] -!- asdfasd [asdfasd!~332332@2.216.236.95] has joined #linuxcnc
[06:22:38] -!- Tecan has quit [Ping timeout: 256 seconds]
[06:24:47] -!- JohnyK [JohnyK!~wity@witypc.ynet.sk] has joined #linuxcnc
[06:44:05] -!- mhaberler has quit [Quit: mhaberler]
[06:48:23] -!- mhaberler [mhaberler!~mhaberler@193.228.47.221] has joined #linuxcnc
[06:53:09] -!- mhaberler has quit [Ping timeout: 245 seconds]
[06:56:52] -!- Deejay [Deejay!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[06:57:01] <Deejay> moin
[06:58:29] -!- mhaberler [mhaberler!~mhaberler@bigmac.stiwoll.mah.priv.at] has joined #linuxcnc
[07:12:05] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[07:13:03] -!- rootB has quit []
[07:35:53] -!- Flipp_ has quit [Ping timeout: 244 seconds]
[07:40:13] -!- nofxx_ has quit [Ping timeout: 252 seconds]
[07:50:13] -!- podarok [podarok!~podarok@host-176-38-13-39.la.net.ua] has joined #linuxcnc
[07:52:27] -!- Akex [Akex!uid58281@gateway/web/irccloud.com/x-bugslgckpvaosbyp] has joined #linuxcnc
[08:08:32] -!- mk0 [mk0!~Orr@plasmoteg-1.bas-net.by] has joined #linuxcnc
[08:09:02] micges_ is now known as micges
[08:38:19] -!- f1oat3 [f1oat3!~f1oat@AMontsouris-553-1-22-87.w92-151.abo.wanadoo.fr] has joined #linuxcnc
[08:43:19] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[08:46:32] -!- _1SheYode has quit []
[08:47:16] -!- eventor [eventor!~eventor@p5DDD7892.dip0.t-ipconnect.de] has joined #linuxcnc
[08:50:29] -!- gambakufu [gambakufu!~ah@bzq-79-183-58-115.red.bezeqint.net] has joined #linuxcnc
[09:02:21] -!- theorb has quit [Ping timeout: 252 seconds]
[09:06:35] -!- rob_h [rob_h!~robh@94.3.108.134] has joined #linuxcnc
[09:11:42] -!- theorb [theorb!~theorb@cpc3-swin16-2-0-cust28.3-1.cable.virginm.net] has joined #linuxcnc
[09:16:55] -!- f1oat3 has quit [Read error: Connection reset by peer]
[09:17:25] -!- f1oat3 [f1oat3!~f1oat@AMontsouris-553-1-22-87.w92-151.abo.wanadoo.fr] has joined #linuxcnc
[09:19:20] -!- membiblio [membiblio!~membiblio@108.32.57.2] has joined #linuxcnc
[09:19:36] -!- membiblio has quit [Client Quit]
[09:20:00] -!- membiblio [membiblio!~membiblio@108.32.57.2] has joined #linuxcnc
[09:23:44] <membiblio> Good Morning
[09:24:04] -!- gambakufu has quit []
[09:26:08] -!- sirdancealot has quit [Remote host closed the connection]
[09:28:15] -!- gambakufu [gambakufu!~ah@bzq-79-183-58-115.red.bezeqint.net] has joined #linuxcnc
[09:28:37] -!- podarok has quit [Ping timeout: 264 seconds]
[09:32:15] -!- sirdancealot [sirdancealot!~koo5@236.152.broadband3.iol.cz] has joined #linuxcnc
[09:33:37] -!- JohnyK has quit [Ping timeout: 264 seconds]
[09:36:44] -!- membiblio [membiblio!~membiblio@108.32.57.2] has parted #linuxcnc
[09:43:57] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[09:44:16] -!- sumpfralle [sumpfralle!~lars@subaru.opennet-initiative.de] has joined #linuxcnc
[09:45:45] -!- JohnyK [JohnyK!~wity@witypc.ynet.sk] has joined #linuxcnc
[09:56:54] -!- JohnyK has quit [Read error: Connection reset by peer]
[09:57:23] -!- dutchfish [dutchfish!~wil@unaffiliated/dutchfish] has joined #linuxcnc
[10:21:28] -!- FreezingCold [FreezingCold!~FreezingC@135.0.41.14] has joined #linuxcnc
[10:28:53] -!- skunkworks has quit [Ping timeout: 252 seconds]
[10:30:29] -!- podarok [podarok!~podarok@host-176-38-13-39.la.net.ua] has joined #linuxcnc
[10:34:26] -!- moorbo [moorbo!~moorbo@dyn-21-121.mdm.its.uni-kassel.de] has joined #linuxcnc
[11:33:19] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[11:53:39] -!- sirdancealot has quit [Ping timeout: 250 seconds]
[11:56:32] -!- skunkworks [skunkworks!~skunkwork@68-115-41-210.static.eucl.wi.charter.com] has joined #linuxcnc
[12:02:26] -!- somenewguy [somenewguy!~butts@pool-173-76-235-209.bstnma.fios.verizon.net] has joined #linuxcnc
[12:03:25] -!- teepee has quit [Ping timeout: 264 seconds]
[12:22:41] -!- micges has quit [Ping timeout: 250 seconds]
[13:04:06] -!- micges has quit [Ping timeout: 250 seconds]
[13:09:41] -!- Valen has quit [Remote host closed the connection]
[13:20:44] -!- Tecan [Tecan!~fasdf@unaffiliated/unit41] has joined #linuxcnc
[13:22:14] -!- per_sonne_ has quit [Ping timeout: 264 seconds]
[13:53:15] -!- djinni` has quit [*.net *.split]
[13:53:16] -!- theorb has quit [*.net *.split]
[13:53:16] -!- erve has quit [*.net *.split]
[13:53:16] -!- _rob has quit [*.net *.split]
[13:53:16] -!- pcw_home has quit [*.net *.split]
[13:53:16] -!- MacGalempsy has quit [*.net *.split]
[13:53:16] -!- SpeedEvil has quit [*.net *.split]
[13:53:16] -!- raymondhim has quit [*.net *.split]
[13:53:16] -!- postaL has quit [*.net *.split]
[13:53:17] -!- Brunetty has quit [*.net *.split]
[13:53:17] -!- seb_kuzminsky has quit [*.net *.split]
[13:53:17] -!- dr0w has quit [*.net *.split]
[13:53:18] -!- MattyMatt has quit [*.net *.split]
[13:53:19] -!- Katharsis has quit [*.net *.split]
[13:53:19] -!- Nutter has quit [*.net *.split]
[13:53:19] -!- alex_joni has quit [*.net *.split]
[13:53:20] -!- lnr has quit [*.net *.split]
[13:53:21] -!- RagingComputer has quit [*.net *.split]
[13:53:21] -!- cradek has quit [*.net *.split]
[13:53:21] -!- rbancroft has quit [*.net *.split]
[13:53:22] -!- lexano has quit [*.net *.split]
[13:53:22] -!- _Sync_ has quit [*.net *.split]
[13:53:22] -!- Rab has quit [*.net *.split]
[13:53:23] -!- teepee has quit [*.net *.split]
[13:53:23] -!- FreezingCold has quit [*.net *.split]
[13:53:23] -!- gambakufu has quit [*.net *.split]
[13:53:23] -!- syyl_ has quit [*.net *.split]
[13:53:24] -!- CaptHindsight has quit [*.net *.split]
[13:53:24] -!- wortley_ has quit [*.net *.split]
[13:53:24] -!- SkramX_ has quit [*.net *.split]
[13:53:24] -!- amatecha has quit [*.net *.split]
[13:53:24] -!- sweenzor has quit [*.net *.split]
[13:53:25] -!- jfrmilner has quit [*.net *.split]
[13:53:25] -!- smartatt1ck has quit [*.net *.split]
[13:53:26] -!- cmorley has quit [*.net *.split]
[13:53:27] -!- tumdedum has quit [*.net *.split]
[13:53:27] -!- varesa has quit [*.net *.split]
[13:53:28] -!- cpresser has quit [*.net *.split]
[13:53:28] -!- Khetzal has quit [*.net *.split]
[13:53:28] -!- i_tarzan has quit [*.net *.split]
[13:53:29] -!- c_morley has quit [*.net *.split]
[13:53:30] -!- Virtakuono has quit [*.net *.split]
[13:53:30] -!- BlaDe^ has quit [*.net *.split]
[13:53:30] -!- ssi has quit [*.net *.split]
[13:53:30] -!- elderx_ has quit [*.net *.split]
[13:53:31] -!- sumpfralle has quit [*.net *.split]
[13:53:31] -!- Deejay has quit [*.net *.split]
[13:53:31] -!- arekm has quit [*.net *.split]
[13:53:31] -!- WalterN has quit [*.net *.split]
[13:53:32] -!- Cromaglious has quit [*.net *.split]
[13:53:33] -!- MrFahrenheit has quit [*.net *.split]
[13:53:33] -!- zeeshan has quit [*.net *.split]
[13:53:33] -!- s1dev has quit [*.net *.split]
[13:53:33] -!- rup3rt has quit [*.net *.split]
[13:53:33] -!- sheppard has quit [*.net *.split]
[13:53:34] -!- pjm has quit [*.net *.split]
[13:53:34] -!- MarkusBec has quit [*.net *.split]
[13:53:35] -!- racicot has quit [*.net *.split]
[13:53:36] -!- _methods has quit [*.net *.split]
[13:53:36] -!- q3k has quit [*.net *.split]
[13:53:36] -!- rclsilver has quit [*.net *.split]
[13:53:37] -!- dutchfish has quit [*.net *.split]
[13:53:37] -!- eventor has quit [*.net *.split]
[13:53:39] -!- HeXiLeD has quit [*.net *.split]
[13:53:39] -!- Jymmm has quit [*.net *.split]
[13:53:39] -!- jesseg has quit [*.net *.split]
[13:53:39] -!- icecube45 has quit [*.net *.split]
[13:53:39] -!- jdh has quit [*.net *.split]
[13:53:40] -!- Lowridah has quit [*.net *.split]
[13:53:40] -!- tris has quit [*.net *.split]
[13:53:42] -!- kanzure has quit [*.net *.split]
[13:53:42] -!- _nexxus_ has quit [*.net *.split]
[13:53:42] -!- roh has quit [*.net *.split]
[13:53:42] -!- uwe_mobile has quit [*.net *.split]
[13:53:43] tris- is now known as tris
[13:53:49] -!- FreezingCold [FreezingCold!~FreezingC@135.0.41.14] has joined #linuxcnc
[13:54:38] -!- djinni` [djinni`!~djinni@105.ip-167-114-152.net] has joined #linuxcnc
[13:55:21] -!- lnr [lnr!~lnr@aim.engr.arizona.edu] has joined #linuxcnc
[13:55:21] -!- gambakufu [gambakufu!~ah@bzq-79-183-58-115.red.bezeqint.net] has joined #linuxcnc
[13:55:21] -!- syyl_ [syyl_!~sg@p200300632C3F1204B15D88C938624C36.dip0.t-ipconnect.de] has joined #linuxcnc
[13:55:21] -!- CaptHindsight [CaptHindsight!~2020@unaffiliated/capthindsight] has joined #linuxcnc
[13:55:21] -!- jfrmilner [jfrmilner!~jfrmilner@ip-77-221-186-85.dsl.twang.net] has joined #linuxcnc
[13:55:21] -!- smartatt1ck [smartatt1ck!~petem@192.81.213.49] has joined #linuxcnc
[13:55:21] -!- cmorley [cmorley!~chris@S0106204e7f8c229b.no.shawcable.net] has joined #linuxcnc
[13:55:21] -!- tumdedum [tumdedum!~tumdedum@unaffiliated/espiral] has joined #linuxcnc
[13:55:21] -!- varesa [varesa!~varesa@ec2-54-171-127-114.eu-west-1.compute.amazonaws.com] has joined #linuxcnc
[13:55:21] -!- cpresser [cpresser!~cpresser@rstenpresser.de] has joined #linuxcnc
[13:55:21] -!- i_tarzan [i_tarzan!~i_tarzan@189.249.250.75] has joined #linuxcnc
[13:55:21] -!- c_morley [c_morley!~chris@S0106204e7f8c229b.no.shawcable.net] has joined #linuxcnc
[13:55:21] -!- ssi [ssi!~ssi@app2.prototechnical.com] has joined #linuxcnc
[13:55:52] -!- lnr has quit [Max SendQ exceeded]
[13:56:43] -!- sumpfralle [sumpfralle!~lars@subaru.opennet-initiative.de] has joined #linuxcnc
[13:56:43] -!- Deejay [Deejay!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[13:56:43] -!- arekm [arekm!~arekm@pld-linux/arekm] has joined #linuxcnc
[13:56:43] -!- WalterN [WalterN!~Octavia@71-84-132-102.dhcp.knwc.wa.charter.com] has joined #linuxcnc
[13:56:43] -!- Cromaglious [Cromaglious!~robi@pool-108-23-106-180.lsanca.fios.verizon.net] has joined #linuxcnc
[13:56:43] -!- MrFahrenheit [MrFahrenheit!~hamzadis@unaffiliated/rageofthou] has joined #linuxcnc
[13:56:43] -!- zeeshan [zeeshan!~kvirc64@CPE0018e7cea342-CM5039555db2cc.cpe.net.cable.rogers.com] has joined #linuxcnc
[13:56:43] -!- s1dev [s1dev!~s1dev@199.241.28.135] has joined #linuxcnc
[13:56:43] -!- pjm [pjm!~pjm@uhfsatcom.plus.com] has joined #linuxcnc
[13:56:43] -!- MarkusBec [MarkusBec!znc@80.69.39.131] has joined #linuxcnc
[13:56:43] -!- _methods [_methods!~minotaur@192.81.210.43] has joined #linuxcnc
[13:56:43] -!- q3k [q3k!~q3k@q3k.org] has joined #linuxcnc
[13:56:49] -!- lnr [lnr!~lnr@aim.engr.arizona.edu] has joined #linuxcnc
[13:58:18] -!- `Nerobro [`Nerobro!~wolfeman@fg300a.skylan.net] has joined #linuxcnc
[13:58:18] -!- theorb [theorb!~theorb@cpc3-swin16-2-0-cust28.3-1.cable.virginm.net] has joined #linuxcnc
[13:58:18] -!- _rob [_rob!~rob@host86-134-239-67.range86-134.btcentralplus.com] has joined #linuxcnc
[13:58:18] -!- pcw_home [pcw_home!~chatzilla@c-50-143-148-115.hsd1.ca.comcast.net] has joined #linuxcnc
[13:58:18] -!- MacGalempsy [MacGalempsy!~quassel@ip72-204-45-74.fv.ks.cox.net] has joined #linuxcnc
[13:58:18] -!- SpeedEvil [SpeedEvil!~quassel@tor/regular/SpeedEvil] has joined #linuxcnc
[13:58:18] -!- raymondhim [raymondhim!~raymondhi@c-66-41-216-194.hsd1.mn.comcast.net] has joined #linuxcnc
[13:58:18] -!- postaL [postaL!~postaL@c-107-3-170-109.hsd1.ca.comcast.net] has joined #linuxcnc
[13:58:18] -!- Brunetty [Brunetty!~Home@unaffiliated/brunetty] has joined #linuxcnc
[13:58:18] -!- seb_kuzminsky [seb_kuzminsky!~seb@174-16-215-53.hlrn.qwest.net] has joined #linuxcnc
[13:58:18] -!- dr0w [dr0w!~george@loudsl01-253-117-18.c.iglou.com] has joined #linuxcnc
[13:58:18] -!- MattyMatt [MattyMatt!~matt@cpc12-birk7-2-0-cust211.1-3.cable.virginm.net] has joined #linuxcnc
[13:58:18] -!- Nutter [Nutter!~hehe@server.mesophase.com] has joined #linuxcnc
[13:58:18] -!- alex_joni [alex_joni!~alex_joni@81.196.65.201] has joined #linuxcnc
[13:58:18] -!- RagingComputer [RagingComputer!~RagingCom@ragingcomputer.net] has joined #linuxcnc
[13:58:18] -!- Rab [Rab!reboots@leon.g-cipher.net] has joined #linuxcnc
[13:58:18] -!- cradek [cradek!~chris@outpost.timeguy.com] has joined #linuxcnc
[13:58:18] -!- lexano [lexano!~lexano@CPEa021b7ac59c9-CMbcc81006f6ee.cpe.net.cable.rogers.com] has joined #linuxcnc
[13:58:18] -!- _Sync_ [_Sync_!~foobar@sync-hv.de] has joined #linuxcnc
[13:58:28] tris is now known as 7F1AALP94
[13:58:41] -!- icecube45 [icecube45!~icecube45@h-66-167-204-47.snva.ca.dynamic.megapath.net] has joined #linuxcnc
[13:58:42] -!- dutchfish [dutchfish!~wil@unaffiliated/dutchfish] has joined #linuxcnc
[13:58:42] -!- eventor [eventor!~eventor@p5DDD7892.dip0.t-ipconnect.de] has joined #linuxcnc
[13:58:42] -!- Jymmm [Jymmm!~jymmm@unaffiliated/jymmm] has joined #linuxcnc
[13:58:42] -!- jesseg [jesseg!~jesseg@64.146.180.237] has joined #linuxcnc
[13:58:42] -!- jdh [jdh!~jdh@miranda.org] has joined #linuxcnc
[13:58:42] -!- Lowridah [Lowridah!lowridah@lowridah.com] has joined #linuxcnc
[13:58:42] -!- tris [tris!tristan@65.50.210.30] has joined #linuxcnc
[13:58:42] -!- kanzure [kanzure!~kanzure@unaffiliated/kanzure] has joined #linuxcnc
[13:58:42] -!- _nexxus_ [_nexxus_!~bwg@ragnar.generalamalgamated.com] has joined #linuxcnc
[13:58:42] -!- uwe_mobile [uwe_mobile!~uwe@static.88-198-8-117.clients.your-server.de] has joined #linuxcnc
[13:58:42] -!- roh [roh!~roh@yamato.hyte.de] has joined #linuxcnc
[13:58:46] -!- HeXiLeD has quit [Read error: Connection reset by peer]
[13:59:42] -!- icecube45 has quit [Changing host]
[13:59:42] -!- icecube45 [icecube45!~icecube45@unaffiliated/icecube45] has joined #linuxcnc
[14:03:02] -!- sirdancealot [sirdancealot!~koo5@236.152.broadband3.iol.cz] has joined #linuxcnc
[14:03:45] -!- HeXiLeD has quit [Ping timeout: 252 seconds]
[14:09:28] <_methods> lol freenode goin full retard
[14:13:41] -!- JohnyK [JohnyK!~wity@witypc.ynet.sk] has joined #linuxcnc
[14:20:31] -!- moorbo has quit []
[14:31:11] -!- mk0 has quit [Read error: Connection reset by peer]
[14:50:12] <ssi> lol
[14:56:46] -!- dirty_d [dirty_d!~dirty_d@50-205-178-174-static.hfc.comcastbusiness.net] has joined #linuxcnc
[14:57:43] <dirty_d> lol crap, the fuel pump i bought is 0.1" too big to fit in my fuel tank
[14:58:30] <dirty_d> i think the plastic is thick enough to bore out that much more though
[15:01:56] <dirty_d> hmm, actually that other hole looks big enough
http://www.ebay.com/itm/1988-Kawasaki-550-Fuel-Gas-Tank-With-Pickup-JS550-300-440-SX-/251902698357?hash=item3aa6922375&vxp=mtr
[15:04:34] <dirty_d> need to make a new cap thing out of brass that will have brass hose barbs soldered on for the pump and return line and vent
http://www.3dvieweronline.com/share/NjMadtSG1j8JFUM/NjMadtSG1j8JFUM
[15:05:02] <dirty_d> little holes for the fuel pump wires, should i just use RTV to seal the wires?
[15:10:35] -!- per_sonne_ has quit [Ping timeout: 250 seconds]
[15:31:13] -!- syyl_ws [syyl_ws!~sg@p200300632C3F1204020D60FFFE678AE7.dip0.t-ipconnect.de] has joined #linuxcnc
[15:32:53] amnesic_away is now known as amnesic
[15:32:59] <Cromaglious> yep or silicone
[16:01:52] -!- sirdancealot has quit [Remote host closed the connection]
[16:04:41] -!- capricorn_1 has quit [Quit: Konversation terminated!]
[16:13:54] -!- The_Ball has quit [Ping timeout: 250 seconds]
[16:26:16] -!- mhaberler_ [mhaberler_!~mhaberler@bigmac.stiwoll.mah.priv.at] has joined #linuxcnc
[16:26:36] -!- The_Ball [The_Ball!~ballen@c114-77-179-73.hillc3.qld.optusnet.com.au] has joined #linuxcnc
[16:26:39] -!- mhaberler has quit [Ping timeout: 250 seconds]
[16:26:39] mhaberler_ is now known as mhaberler
[16:31:28] -!- The_Ball has quit [Ping timeout: 272 seconds]
[16:32:05] -!- The_Ball [The_Ball!~ballen@c114-77-179-73.hillc3.qld.optusnet.com.au] has joined #linuxcnc
[16:34:36] -!- Brunetty has quit [Read error: Connection reset by peer]
[16:35:24] -!- Brunetty [Brunetty!~Home@unaffiliated/brunetty] has joined #linuxcnc
[16:36:57] -!- The_Ball has quit [Ping timeout: 265 seconds]
[16:37:56] -!- The_Ball [The_Ball!~ballen@c114-77-179-73.hillc3.qld.optusnet.com.au] has joined #linuxcnc
[16:44:16] -!- kwallace has quit [Ping timeout: 256 seconds]
[16:51:13] -!- patrickarlt has quit [Ping timeout: 245 seconds]
[16:52:11] amnesic is now known as amnesic_away
[16:54:47] -!- The_Ball has quit [Read error: Connection timed out]
[16:56:36] -!- per_sonne_ has quit [Ping timeout: 240 seconds]
[16:57:19] -!- dimas has quit [Quit: õÈÏÖÕ Ñ ÏÔ ×ÁÓ (xchat 2.4.5 ÉÌÉ ÓÔÁÒÛÅ)]
[17:02:08] <Connor> http://www.newegg.com/Product/Product.aspx?Item=N82E16815580004
[17:02:21] <Connor> wonder how that would do with a ethernet mesa card..
[17:03:11] amnesic_away is now known as amnesic
[17:04:32] -!- adb [adb!~IonMoldov@2a02:1205:c6a9:72a0:baac:6fff:fe67:305f] has joined #linuxcnc
[17:08:52] -!- sumpfralle has quit [Ping timeout: 244 seconds]
[17:10:09] -!- moorbo [moorbo!~moorbo@dyn-21-121.mdm.its.uni-kassel.de] has joined #linuxcnc
[17:10:40] <Cromaglious> you look at raspberrypi 2?
[17:10:59] -!- micges [micges!~micges@acvc127.neoplus.adsl.tpnet.pl] has joined #linuxcnc
[17:16:42] <XXCoder> Connor: there is newer version of that
[17:16:54] <Connor> Is there?
[17:17:12] <Connor> Question remains.. wonder how it would do.. :)
[17:17:24] <XXCoder> theres banner at top of that page
[17:17:26] <ssi> buy one and try it
[17:17:31] <zeeshan> ssi shush
[17:17:34] <ssi> NO U
[17:17:59] <XXCoder> well near top anyway
[17:18:03] <Cromaglious> rp2 is .9ghz 1Mb
[17:18:10] <ssi> XXCoder: I got some of the spaceman shit in the mail this weekend
[17:18:15] <ssi> had one for lunch yesterday and having one now
[17:18:37] <XXCoder> hows it so far?
[17:18:45] <ssi> tastes like ovaltine full of sunflower seeds
[17:18:48] <Cromaglious> $35, with 11n and ps it's $60
[17:19:15] <zeeshan> pci express x16
[17:19:27] <zeeshan> 5i25 works with that yea?
[17:19:30] <XXCoder> ssi: I do recommand adding flavors, like hot choculate powder to it. taste better
[17:19:39] <XXCoder> I never liked any version of soylent taste.
[17:19:39] <ssi> XXCoder: this one's already chocolate flavored
[17:19:45] <XXCoder> oh
[17:19:53] <ssi> I got the sample pack, which is his three blends, in both chocolte and raw
[17:19:56] <ssi> the chocolate ones aren't bad
[17:19:58] <ssi> not sure how the raw will be
[17:20:11] <XXCoder> oh DIY soylent?
[17:20:34] <ssi> it's this one:
http://www.newegg.com/Product/Product.aspx?Item=N82E16815580004
[17:20:36] <ssi> er
[17:20:40] <ssi> http://www.spacenutrientsstation.com/buy
[17:20:48] <ssi> one of thediy guys is selling them quickly
[17:21:00] <ssi> I ordered another one from one of the DIY guys as well but I haven't received it yet
[17:21:08] <ssi> ordered a few things since the production soylent is so far back ordered
[17:21:38] <XXCoder> hmm yeah. soylent is still backlog by week or so now. much better than 7 months I waited. lol
[17:21:42] <Cromaglious> .0
[17:21:48] <Cromaglious> .
[17:21:51] <ssi> it's four weeks on initial orders
[17:22:00] <Cromaglious> 3021154
[17:22:11] <Cromaglious> kitty typing
[17:22:15] <ssi> lol
[17:22:38] <Cromaglious> kkkkkkkkkkkkkkkkkkkkkkjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjjj
[17:22:44] <Cromaglious> dang kat
[17:22:45] <XXCoder> heh I remember theres a program for detecting that and stop it
[17:23:07] <Cromaglious> ok Off she goes to her perch
[17:23:14] <XXCoder> ssi: did you order a week og soylent though?
[17:23:25] -!- sumpfralle [sumpfralle!~lars@p5DCFD3E1.dip0.t-ipconnect.de] has joined #linuxcnc
[17:23:34] <ssi> XXCoder: yeah
[17:23:45] <XXCoder> cool. once it arrives reorders will be fast
[17:23:52] <ssi> and a week of the schmoylent (one of the other diy ones), and six meals of the spaceman stuff
[17:24:08] <ssi> I'll probably end up doing diy at some point
[17:24:15] <XXCoder> diy stuff is less tested
[17:24:16] <ssi> I just need to try some of the different recipes
[17:25:32] <XXCoder> cool :)
[17:25:33] -!- mozmck [mozmck!~moses@67.210.159.245] has parted #linuxcnc
[17:25:46] <ssi> so far it's fulfilling one of the major goals I had, w
[17:25:53] <ssi> which is to have something I can eat for lunch at my desk at work
[17:25:58] <ssi> that's EASY to do
[17:27:49] <ssi> http://holycrap.com
[17:27:50] <ssi> ahahahaha
[17:28:22] <XXCoder> heh people trying to catch Soylent up
[17:28:55] <ssi> turns out the guy that started soylent is a frat brother of my ex-gf's cousin
[17:29:04] <XXCoder> nice lol
[17:30:11] -!- nofxx_ [nofxx_!~nofxx@unaffiliated/nofxx] has joined #linuxcnc
[17:30:55] <MrHindsight> I missed the backstory on the soylent stuff. What is it?
[17:31:05] <dirty_d> people
[17:31:05] <XXCoder> its boring meal
[17:31:23] <MrHindsight> saw the movie, what's in it?
[17:31:23] <XXCoder> but whats awesome is it is very healthy meal for just $3 per meal
[17:31:31] <ssi> diethacking
[17:31:35] <XXCoder> and easy to make.
[17:31:53] <XXCoder> MrHindsight: movie green soylent is made from humans, book it's not.
[17:33:03] <MrHindsight> so it's not a solution to over population?
[17:33:22] <XXCoder> lol nope
[17:33:42] <ssi> well they sort of claim it is
[17:34:06] <XXCoder> the movie or current actual soylent site?
[17:34:12] <ssi> the current site
[17:34:28] <ssi> I thought I saw somewhere on there about it being a solution to feeding growing populations
[17:34:32] <ssi> but whatever
[17:34:36] <ssi> I don't care about poor people
[17:35:03] <XXCoder> ssi: it is, but know what? people with secure food, livinghood and house tend to have less kids
[17:35:13] <XXCoder> indirectly it may work like that
[17:35:18] <ssi> maybe
[17:35:41] <jdh> cause or effect?
[17:37:00] <jdh> smart people have fewer children?
[17:37:11] <XXCoder> not nesscarily
[17:38:57] -!- micges has quit [Quit: Ex-Chat]
[17:39:38] <jdh> having 10 kids gives better odds in old age support lottery?
[17:40:30] <XXCoder> jdh: thats a myth
[17:40:43] <XXCoder> support bump only for first 2 kids
[17:40:53] <jdh> ssi: if it weren't for poor people who would do all those bad jobs?
[17:41:16] <zeeshan> my dads a dentist
[17:41:19] <zeeshan> hes got 9 kids total
[17:41:20] <zeeshan> lol
[17:41:29] <zeeshan> your theory is out the window!
[17:41:34] <XXCoder> jdh: so you want more poor?
[17:41:53] <zeeshan> in our culture , we have kids
[17:41:59] <zeeshan> westerners have dogs :)
[17:42:04] <ssi> jdh: poor people in america don't do any jobs as it is :P
[17:42:19] <jdh> nah, that's the tea party
[17:42:35] <XXCoder> zeeshan: sorry but I bust your view - I don't have kids nor dogs lol
[17:42:44] <zeeshan> haha
[17:42:48] <zeeshan> im being ignorant :)
[17:44:10] <zeeshan> so that part i made yesterday -- my friend told me what it is for
[17:44:13] <zeeshan> and i made one for myself
[17:44:54] <zeeshan> http://i.imgur.com/Gyn5s1S.jpg
[17:45:16] <zeeshan> it works for both rhd and lhd vehicles!
[17:45:34] <XXCoder> offset?
[17:45:44] <zeeshan> its just a mirror
[17:45:45] <zeeshan> of each other
[17:46:20] <XXCoder> whats it for though
[17:46:33] <zeeshan> to hold up a prorportional valve for example
[17:46:36] <XXCoder> high pressure oil? power steer>?
[17:46:43] <zeeshan> brakes
[17:47:00] <XXCoder> so it converts little motion to larger or other way?
[17:47:02] -!- patricka_ has quit [Remote host closed the connection]
[17:47:22] <zeeshan> it sets the proportional of brake pressure that makes it to the rear brake calipers vs front
[17:47:27] <zeeshan> *proportion
[17:47:30] <XXCoder> ahh
[17:52:59] -!- danylevskyi has quit [Ping timeout: 256 seconds]
[17:54:15] -!- Brunetty has quit [Read error: Connection reset by peer]
[17:57:05] <CaptHindsight> Jymmm: have you found a reputable UV flashlight dealer in the USA?
http://shop.ledwholesalers.com/index.php?route=product/product&path=41&product_id=398 looking for similar ~385nm, 10-30W
[17:57:54] -!- Brunetty [Brunetty!~Home@unaffiliated/brunetty] has joined #linuxcnc
[18:02:41] <Cromaglious> Tubalcaine selling some stuff
http://www.ebay.com/sch/mrpete2/m.html?_nkw=&_armrs=1&_ipg=&_from=
[18:02:44] <CaptHindsight> http://www.ebay.com/itm/10W-UV-Ultra-Voilet-High-Power-led-Bead-385nm-390nm-for-led-lamp-source-/331429800492 I already have a bunch of these and much larger >100w but I want to buy a complete lamp vs build something
[18:04:19] <ssi> XXCoder:
http://custombodyfuel.com/2015/01/the-case-for-crickets/
[18:04:37] <XXCoder> yeah read that already
[18:04:41] <ssi> heheh
[18:04:49] <ssi> I ordered his sampler kit too
[18:04:54] <ssi> I'm interested to see how that is
[18:06:04] <XXCoder> yeah too bad its so expensive
[18:06:15] <ssi> what, the cricket? or his sampler
[18:06:21] <ssi> cause his sampler is priced the same as soylent
[18:06:30] <XXCoder> cricket
[18:06:35] <ssi> yea I don't want cricket :)
[18:08:32] -!- patrickarlt has quit [Read error: Connection reset by peer]
[18:08:36] <XXCoder> bugjuice lol
[18:10:47] <XXCoder> talking about bugjuice
[18:10:54] <XXCoder> anyone remember beetlejuice? lol
[18:11:12] <Jymmm> beetlejuice beetlejuice beetlejuice
[18:13:22] <zeeshan> hey maybe someone in here knows
[18:13:26] <zeeshan> http://i.imgur.com/Gyn5s1S.jpg
[18:13:29] <zeeshan> the t in the background
[18:13:38] <zeeshan> is there some sort of clamp you can purchase to secure that against the firewall
[18:13:56] <XXCoder> wire clamp maybe
[18:14:01] <ssi> adel clamp
[18:14:15] <XXCoder> tv cable holder probablu right size
[18:14:23] <ssi> http://www.aircraftspruce.com/catalog/appages/ms21919clamps.php
[18:14:29] <zeeshan> i dont wanna secure the tubes
[18:14:33] <zeeshan> i wanna secure the t
[18:14:36] <XXCoder> ssi: ah so its called adel clamp cool
[18:14:53] <zeeshan> XXCoder: i think a wire clamp might work
[18:14:56] <zeeshan> if i can find one thin enough
[18:15:11] <zeeshan> https://encrypted-tbn1.gstatic.com/images?q=tbn:ANd9GcRGsojCIKI2Aa4DMdtmAQoZia7IWVx4aGrtPvyv-ODnaiPSXdGl
[18:16:14] <zeeshan> https://encrypted-tbn2.gstatic.com/images?q=tbn:ANd9GcRTzfyQay57GXhhWmA3eizXCr6cu1tHphl6_ukKTk2VMxzr_5EtaA
[18:16:17] <zeeshan> i was thinking of making something like this
[18:16:24] <zeeshan> but with a square hole
[18:16:43] <XXCoder> not sure whats different between securing T or hoses sides of it
[18:17:17] <zeeshan> securing the t would be stiffer
[18:17:24] <Rab> The tee has the mass, that's what you want to secure.
[18:17:34] <XXCoder> makes sense I guess
[18:17:47] -!- patrickarlt has quit [Read error: Connection reset by peer]
[18:17:52] <zeeshan> i'd think of the copper nickel line as a floppy noodle
[18:18:12] <zeeshan> thats hold a .5lb chunk of steel
[18:18:21] <zeeshan> :P
[18:19:11] -!- amiri_ has quit [Ping timeout: 246 seconds]
[18:19:48] <Rab> zeeshan, I dunno if this is a serious contender...but metal zip tie holder is an interesting option:
https://accuglassproducts.com/product.php?productid=16966
[18:20:28] <XXCoder> Rab: not bad idea. 2 adel clamps on sides, and that zip tie holders securing T to adel clamps
[18:20:56] -!- brlcad has quit [Ping timeout: 252 seconds]
[18:21:03] <zeeshan> hmm
[18:23:01] -!- sumpfralle has quit [Quit: Leaving.]
[18:23:04] -!- sumpfralle1 [sumpfralle1!~lars@p5DCFD3E1.dip0.t-ipconnect.de] has joined #linuxcnc
[18:23:34] -!- karavanjo has quit [Ping timeout: 272 seconds]
[18:25:03] <zeeshan> thought about it
[18:25:23] <zeeshan> ill make a hole in an aluminum flat bar to pass 2 stainless clamps through
[18:25:27] <zeeshan> and then mount that plate to the fire wall
[18:25:42] <zeeshan> that flat bar will act like a spacer too
[18:25:44] <XXCoder> isnt holes bad for fire wall?
[18:25:55] <zeeshan> im calling it fire wall
[18:26:01] <zeeshan> but its the sill thing above it
[18:26:04] <zeeshan> where water collects
[18:26:06] <XXCoder> oh
[18:26:09] <zeeshan> not the actual fire wall :P
[18:26:24] <zeeshan> basically where the oem tie points are
[18:27:10] <zeeshan> or i can just CNC a bracket!
[18:27:27] <zeeshan> drill a hole, and then use a smaller end mill to square it out
[18:28:34] -!- sumpfralle1 has quit [Ping timeout: 245 seconds]
[18:31:39] -!- brlcad has quit [Ping timeout: 250 seconds]
[18:36:10] -!- syyl_ws has quit [Remote host closed the connection]
[18:37:08] <jdh> why drill?
[18:37:43] <zeeshan> you can remove like .5" material like that
[18:37:49] <zeeshan> in like 10 sec
[18:38:03] <zeeshan> vs using a 1/16" dinky end mill for an hour cause you're afraid to break it :P
[18:38:14] <zeeshan> just use it to clean up the corners
[18:38:58] <ssi> agreed
[18:39:44] <jdh> I need better toolholders
[18:40:21] <jdh> drill to end mill is time consuming for me
[18:41:54] <_rob> anyone got an opinion on this mill for the money :
http://www.axminster.co.uk/axminster-engineer-series-sx3-mill-drill
[18:42:04] <_rob> its a SEIG SX3
[18:42:47] <_rob> there is also this one,
http://www.axminster.co.uk/axminster-engineer-series-xn2-mill-drill
[18:42:51] <_rob> similar money
[18:43:54] <dirty_d> i was stuck between the SX3 and G0704
[18:44:03] <dirty_d> i went with the G0704 for some reason I dont remember
[18:44:06] <jdh> me too
[18:44:15] <jdh> more travel
[18:44:22] <dirty_d> yea that was one reason, i think there was another
[18:44:37] <dirty_d> I think maybe build quality or something
[18:44:55] <jdh> sx3 has more features discarded for cnc
[18:45:12] <_rob> im in the UK so theres less options
[18:45:23] <jdh> bf20
[18:45:48] <_rob> ahh
[18:45:48] -!- per_sonne_ has quit [Ping timeout: 245 seconds]
[18:45:52] <dirty_d> isnt there one bigger but not much more money?
[18:45:55] <dirty_d> RF45 or something maybe
[18:46:07] <_rob> I looked at various RF45 clone mills
[18:46:09] <_rob> cant find one in the UK
[18:46:44] <jdh> wait for a real cnc with dead control?
[18:47:00] <_rob> wait ?
[18:47:10] <_rob> till I have more cash, or ? :)
[18:48:05] <jdh> until one shows up
[18:48:46] <_rob> quite like the idea of converting it myself
[18:48:57] <_rob> prob expensive once I've added ballscrews etc..
[18:49:04] <dirty_d> it is
[18:49:29] <_rob> so how much did you spend all in on your conversion dirty_d ?
[18:49:55] <dirty_d> im not exactly sure, the mill was $1100
[18:50:02] <dirty_d> maybe $2000?
[18:50:05] <dirty_d> no had to be more
[18:50:10] <dirty_d> 2500 - 3000
[18:50:26] <_rob> even $3000 for a quality job (excluding time) is cheaper than anything you can get pre-cnc'd for that money
[18:50:33] <dirty_d> thats counting the cooling and everything
[18:50:35] <dirty_d> tooling*
[18:50:52] <_rob> also, with alot of them your paying for their software development
[18:51:17] -!- sumpfralle [sumpfralle!~lars@p5DCFD3E1.dip0.t-ipconnect.de] has joined #linuxcnc
[18:51:19] -!- gambakufu has quit [Ping timeout: 265 seconds]
[18:51:40] <dirty_d> im pretty happy with it
[18:51:41] <_rob> with linuxcnc thats already saving alot that you'd pay for on a pro cnc machine
[18:51:59] <_rob> cant find too many out there that are hardware only cnc mills
[18:52:04] -!- Tecan has quit [Ping timeout: 272 seconds]
[18:52:09] <_rob> unless they are some small outfit doing conversion jobs
[18:52:40] <dirty_d> if you do convert it yourself, try to use double nut ballscrews
[18:53:29] <_rob> that BF20 is pretty cheap for the size
[18:53:30] <dirty_d> if you wanna interpolate holes with +/- 0.001 accuracy backlash compensation isnt enough
[18:54:32] -!- podarok has quit [Remote host closed the connection]
[18:54:43] <zeeshan> even $3000 for a quality job (excluding time) is cheaper than anything you can get pre-cnc'd for that money
[18:54:45] <zeeshan> ^
[18:54:49] <zeeshan> no its not
[18:54:50] <dirty_d> youd probably need someone with a mill to mill your mill
[18:54:58] -!- ve7it [ve7it!~LawrenceG@S01060014d19d0b68.pk.shawcable.net] has joined #linuxcnc
[18:55:03] <dirty_d> if you use double ballnuts
[18:55:04] <zeeshan> i spent like 2800 on retrofitting my old cnc machine
[18:55:29] <zeeshan> i still cant get backlash out of my lathe's ball screw
[18:55:31] <zeeshan> thats why im bitter
[18:55:37] <zeeshan> for Z axis.
[18:55:48] <_rob> zeeshan, what ready to go cnc machines of similar size for that money ?
[18:55:59] <dirty_d> zeeshan, i have a 70lb counterweight to fix that
[18:56:04] -!- gambakufu [gambakufu!~ah@bzq-79-183-113-91.red.bezeqint.net] has joined #linuxcnc
[18:56:07] <zeeshan> dirty_d: lathe
[18:56:12] <dirty_d> ahh
[18:56:26] <zeeshan> rob none, but i was referring to dirty_d's comment of retrofitting an older machine
[18:56:30] <zeeshan> its the cheapest
[18:56:31] <_rob> ahh
[18:56:44] <zeeshan> if youre in the uk
[18:56:49] <dirty_d> ive seen stuff on craigslist for pretty cheap
[18:56:51] <zeeshan> you have the biggest source of cnc machines in the world!
[18:57:11] <_rob> whos that ?
[18:57:32] <zeeshan> germany is over the pond :)
[18:57:42] <zeeshan> apparently you can buy a maho or deckel for relatively cheap there
[18:57:57] <zeeshan> while youre there, find me a cheap z axis cover :p
[18:58:50] -!- r0ute has quit [Ping timeout: 264 seconds]
[18:59:16] amnesic is now known as amnesic_away
[19:00:09] -!- KimK_laptop [KimK_laptop!~Kim@wsip-70-186-238-216.ks.ks.cox.net] has joined #linuxcnc
[19:00:52] <XXCoder> find me a cnc mill for hmm say $1000 lol
[19:01:02] <XXCoder> none of those tiny ones either
[19:01:32] <zeeshan> i think you can find one for 2000
[19:01:40] <zeeshan> and spend 1000 getting it work
[19:01:44] <zeeshan> maybe i got lucky, i dont know
[19:01:45] <XXCoder> tend to need work. yeah
[19:01:51] <zeeshan> i think i did, because i still cant find a cnc lathe
[19:01:51] <zeeshan> for cheap
[19:01:57] <_rob> what did yo uget for 1000 zeeshan
[19:02:06] <zeeshan> rob i paid 1500 for this:
[19:02:39] <zeeshan> http://i.imgur.com/yc4yhtI.jpg
[19:02:48] <zeeshan> http://i.imgur.com/SrFR1MG.jpg
[19:03:07] <zeeshan> http://i.imgur.com/l5K5A7u.jpg
[19:03:10] <zeeshan> now it looks like that
[19:03:10] <zeeshan> !
[19:03:23] <XXCoder> still in vertical mode eh
[19:03:32] <zeeshan> its in vertical mode right now
[19:03:57] <_rob> lol
[19:04:10] <_rob> very nice
[19:04:16] <_rob> how much work to get it running ?
[19:04:36] <zeeshan> i spent like 4 months making a completely new control for it
[19:04:47] <zeeshan> using amc servo drives
[19:04:47] <Connor> Would have been less work if he would have listened a bit more in the beginning. :)
[19:04:57] <zeeshan> connor listened to what?
[19:05:02] <zeeshan> im happy i went with a completelny new controller
[19:05:18] <zeeshan> minus the mishaps with the amc drives!
[19:05:22] <Connor> zeeshan: at our suggestions. :)
[19:05:36] <_rob> pretty nice tho
[19:05:38] <_rob> and cheap
[19:06:06] <_rob> also huge
[19:06:16] <_rob> well, too big for me
[19:06:28] <_rob> the missus would have a fit if a truck pulled up with that on it
[19:06:40] <XXCoder> even if it was free? heh
[19:06:59] <_rob> still gotta have somewhere to put it
[19:07:12] <_rob> London and Space don't go together
[19:09:20] -!- sirdancealot [sirdancealot!~koo5@236.152.broadband3.iol.cz] has joined #linuxcnc
[19:09:52] <XXCoder> http://hackaday.com/2015/04/03/machining-a-skeleton-clock-in-10000-easy-steps/ dang
[19:15:05] <dirty_d> jesus
[19:15:42] <zeeshan> http://gyazo.com/3b0f03db46298e6b2a39fc138925b93c
[19:15:46] <zeeshan> this is what im thinking for the clamp
[19:15:59] <XXCoder> not bad
[19:16:05] <zeeshan> two set screws to hold tt in place
[19:16:09] <zeeshan> weld green thing to red thing
[19:16:23] <zeeshan> seems like a whole lot of work for holding aT
[19:16:23] <zeeshan> haha
[19:16:29] -!- FinboySlick [FinboySlick!~shark@squal.net] has joined #linuxcnc
[19:16:31] <dirty_d> whats taht for?
[19:16:42] <zeeshan> http://i.imgur.com/Gyn5s1S.jpg
[19:16:45] <zeeshan> trying to secure that t
[19:16:47] <zeeshan> first iteration
[19:16:59] <zeeshan> i still think the stainless zip tie idea is better
[19:17:06] <XXCoder> that guy has talent. all manual, no cnc
[19:17:06] <zeeshan> i just dont have a zip tie gun for stainless
[19:17:07] -!- patrickarlt has quit [Remote host closed the connection]
[19:18:18] <dirty_d> the brass Tee?
[19:18:23] <XXCoder> dirty_d: yeah
[19:18:31] <XXCoder> guys making skeleton clock
[19:18:34] <XXCoder> no cnc
[19:19:06] <dirty_d> sheet metal screws and some U clamps?
[19:19:12] <dirty_d> i dunno if thats what theyre called
[19:19:44] <dirty_d> http://www.hengsin.com/upload_img/U%20CLAMP%20U%20CLAMP.jpg
[19:19:59] <zeeshan> you know
[19:20:09] <zeeshan> the main reason i wasn't thinking of using those is because i have a square profile
[19:20:21] <zeeshan> but i could take some square stock
[19:20:25] <XXCoder> just bend strip of meta
[19:20:27] <zeeshan> and beat that round part into a square
[19:20:32] <XXCoder> or that
[19:20:33] <dirty_d> yea
[19:20:56] <zeeshan> and then put spacers on the back side of to space the T
[19:20:58] <zeeshan> thank u
[19:21:00] <zeeshan> thats a lot less work
[19:21:04] <DaViruz> how about a brake line tee with mounting holes?
[19:21:11] <DaViruz> speaking of a lot less work..
[19:21:12] <DaViruz> :)
[19:21:14] <zeeshan> DaViruz: find me one!
[19:21:39] <DaViruz> http://www.racereadyproducts.com/cnc-accessories/cnc-brake-line-tees/
[19:21:41] <zeeshan> lol first google link
[19:21:43] <XXCoder> zeeshan: superglue. lol.
[19:21:45] <archivist> you have a milling machine, make it
[19:21:48] <DaViruz> fund a couple others as well
[19:22:11] <zeeshan> double flare fittings are a pain to make
[19:22:18] <zeeshan> you really need the cutter for it
[19:22:27] <CaptHindsight> zeeshan: what were those automotive connectors that you use? did they have 1-4 or 8 pin versions or??
[19:22:42] <zeeshan> which ones CaptHindsight
[19:22:56] <CaptHindsight> there looked water tight, snap fit
[19:22:58] <DaViruz> http://www.etrailer.com/Accessories-and-Parts/Titan/T0778500.html
[19:23:09] <DaViruz> that variety seems to be available at several places as well
[19:23:28] <archivist> aluminium is rather the wrong metal for that pressure
[19:23:46] <XXCoder> archivist: clamps it shouldnt matter
[19:23:58] <XXCoder> its not like it will actually hold pressure
[19:24:02] <archivist> I am thinking on the T
[19:24:12] <zeeshan> brake calipers are aluminum
[19:24:19] <zeeshan> but i still wouldn't run an aluminum fitting
[19:24:23] <zeeshan> cause that crap strips so easily
[19:24:31] <zeeshan> brass or steel
[19:24:38] <XXCoder> hmm
[19:24:56] <DaViruz> copper and aluminium are best left unmixed on galvanic grounds as well
[19:25:11] <XXCoder> dirty_d: lol second video at 6:30 it looks like guy is spawning monster egg
[19:25:32] <DaViruz> http://www.jegs.com/i/Earls/361/972051B/10002/-1
[19:25:42] <DaViruz> that one "improves feel of brake pedal" as well ;)
[19:25:47] <zeeshan> you are the man!
[19:25:47] <zeeshan> you are the man!
[19:25:59] <dirty_d> XXCoder, yea i know wtf is that?
[19:26:11] <XXCoder> chemical treatment i GUESS
[19:26:13] -!- f1oat4 [f1oat4!~f1oat@AMontsouris-553-1-75-92.w92-151.abo.wanadoo.fr] has joined #linuxcnc
[19:26:14] <XXCoder> or hardening
[19:26:16] <zeeshan> i trust earls too
[19:26:31] <XXCoder> yup it has hardened color at end
[19:26:56] -!- f1oat3 has quit [Ping timeout: 252 seconds]
[19:27:23] <XXCoder> ythat guy has more talent in his finger than my whole body
[19:27:42] <DaViruz> i have no idea what earls is, but they seem to have quite the variety in flare fittings
[19:29:17] <zeeshan> they make a lot of automotive fittings
[19:29:34] <DaViruz> archivist: i doubt aluminium is an issue, inside diameters in brake fittings are usually tiny so there isn't much surface area to generate force
[19:29:37] <XXCoder> talking about car stuff
[19:29:48] <DaViruz> what zeeshan said about thread stripping may well be an issue though
[19:29:53] <XXCoder> anyone know where I can get new connectors for my IAC
[19:30:12] <XXCoder> iac itself is fine, wires is fine, its connectors that has broken lock so it could slide loose
[19:30:42] <XXCoder> it now has no "stanple" holder
[19:30:53] <DaViruz> XXCoder:
http://www.amazon.com/Black-Zip-Tie-100-Bag/dp/B0001IMMJI
[19:31:14] <XXCoder> DaViruz: I considered that, no way to really secure it
[19:31:44] <XXCoder> I might just use screw, add screw holes to connector (carefully not hitting any pins) and screw will make it stay aligned
[19:31:48] <DaViruz> XXCoder:
http://www.amazon.com/Loctite-1365882-20-Gram-Bottle-Professional/dp/B004Y960MU/ref=sr_1_1?ie=UTF8&qid=1428348697&sr=8-1&keywords=super+glue
[19:31:58] <DaViruz> sorry
[19:31:59] <DaViruz> :)
[19:32:00] <XXCoder> lol
[19:32:05] <DaViruz> what kind of connector is it?
[19:32:33] <XXCoder> a sec
[19:32:47] <XXCoder> https://img407.imageshack.us/img407/6162/iaams8.png
[19:32:51] <XXCoder> yellow, on left
[19:33:01] <XXCoder> this isnt my van model but connector is common
[19:33:24] <DaViruz> lookas like an ordinary JPT
[19:33:47] <DaViruz> 2 pin?
[19:33:51] <XXCoder> 4
[19:34:22] <DaViruz> those are usually keyed
[19:34:26] <XXCoder> though it looks pretty close so I can finally search using correct terms
[19:34:52] <DaViruz> dealership should have it
[19:35:03] <DaViruz> though they usually don't know it themselves..
[19:35:44] <XXCoder> thanks :) it works fine for now but evenually will work loose lol
[19:36:16] <XXCoder> oh and maybe you know this. ,my van idles just fine at Parked mode, but it sometimes runs rough at brake idle
[19:36:27] <XXCoder> (at drive, but staying in location by brake)
[19:38:24] <DaViruz> leaky brake booster would be my guess
[19:38:31] <DaViruz> it it's a gas engine
[19:38:35] <zeeshan> wow
[19:38:42] <zeeshan> no one caries a brake line t with a mounting hole locally
[19:38:43] <zeeshan> lol
[19:38:49] <zeeshan> i calledf like 9 shops
[19:38:51] <XXCoder> DaViruz: mosr suggest its TPS
[19:40:04] <DaViruz> well it's a pretty wild guess, but it would make sense if it's dependant on brake pedal
[19:40:25] <XXCoder> dunno
[19:41:12] <DaViruz> i guess it may well be because of the added load of being in drive
[19:41:22] <DaViruz> putting it in park and pressing the brake could probably rule it out
[19:41:42] <XXCoder> IAC takes over when my van is in park mode so it idles very smoothly
[19:41:54] <XXCoder> I cleaned egr, IAC, and trottle
[19:42:16] <XXCoder> it runs hell of a lot better but still once a while rough idle
[19:42:37] <XXCoder> new termostat too so it finally can warm up properly
[19:44:13] <DaViruz> i don't think putting it in drive disables iac, but i dunno
[19:44:22] <XXCoder> yea might be wrong
[19:45:45] <XXCoder> DaViruz: though I have yet to replace typical bad hose at egr to umm that thingy
[19:46:00] <XXCoder> its common issue for nissan quest lol so gonna fix that first,
[19:47:14] <DaViruz> everything with a three letter acronym is a common issue on cars :P
[19:47:19] <XXCoder> yeah
[19:47:23] <XXCoder> too bad its not 4
[19:48:57] <XXCoder> odd thing is it has rough idle only when warmed up
[19:49:03] <XXCoder> and not in park
[19:53:42] -!- furrywolf [furrywolf!~randyg@70-6-187-227.pools.spcsdns.net] has joined #linuxcnc
[19:55:17] -!- patrickarlt has quit [Remote host closed the connection]
[20:01:43] -!- dirty_d has quit [Quit: Leaving]
[20:04:17] <XXCoder> LOL
https://www.youtube.com/watch?feature=player_embedded&v=WaAu4L2cl4c
[20:07:17] <LeelooMinai> lol...
[20:07:25] -!- skunkworks has quit [Ping timeout: 250 seconds]
[20:07:58] -!- moorbo has quit [Remote host closed the connection]
[20:09:16] -!- MacGalempsy has quit [Ping timeout: 255 seconds]
[20:12:06] -!- MacGalempsy [MacGalempsy!~quassel@ip72-204-45-74.fv.ks.cox.net] has joined #linuxcnc
[20:15:57] -!- Tecan [Tecan!~fasdf@unaffiliated/unit41] has joined #linuxcnc
[20:20:01] <archivist> apart from steam engine I did this over the weekend
http://www.archivist.info/cnc/screw_error/lamp_screw.php
[20:22:54] -!- erve has quit []
[20:23:22] -!- dutchfish has quit [Quit: Splash, leaving the bowl]
[20:25:34] -!- teepee has quit [Ping timeout: 265 seconds]
[20:25:34] teepee_ is now known as teepee
[20:28:18] <JT-Shop> what size hole do I need for a 1" reamer?
[20:28:50] <archivist> depends on the reamer :)
[20:30:19] <_methods> well text book answer would be a .995" hole
[20:30:26] <_methods> for a 1" remaer
[20:30:57] <_methods> i try to get within .010" for reaming to final
[20:31:03] <archivist> google pre-ream-drill-size-chart.pdf seems someone has written something up
[20:31:25] <_methods> hss reamer?
[20:31:44] <archivist> cheating with adjustable reamers is another way
[20:31:47] <_methods> you can get a little gutsier with carbide reamer
[20:31:56] -!- karavanjo has quit [Ping timeout: 240 seconds]
[20:32:23] <archivist> machine v hand too
[20:32:41] -!- skunkworks [skunkworks!~chatzilla@str-broadband-ccmts-ws-26.dsl.airstreamcomm.net] has joined #linuxcnc
[20:35:03] -!- per_sonne_ has quit [Ping timeout: 256 seconds]
[20:37:00] <JT-Shop> yea a chucking HSS reamer
[20:37:36] <JT-Shop> I might have a 63/64 bit
[20:38:35] <Tom_itx> i try to leave no more than .020" if possible and .010 is even better
[20:38:45] <JT-Shop> nope nearest is 15/16"
[20:38:54] <Tom_itx> can you bore it then ream?
[20:39:16] <Tom_itx> steel or aluminum?
[20:40:10] <Tom_itx> .062 might be quite a bit for a reamer
[20:40:38] <JT-Shop> steel top hat looking part 2" long
[20:41:42] <JT-Shop> I better order a 63/64"
[20:41:54] -!- patricka_ has quit [Remote host closed the connection]
[20:42:05] <Tom_itx> or a boring bar
[20:42:15] <Tom_itx> then you won't need so many large drills
[20:42:43] <Tom_itx> i generally buy over 1/2" on an as needed basis
[20:43:01] <Tom_itx> i've got a drawer full :)
[20:43:17] <Deejay> gn8
[20:43:20] <JT-Shop> yea me too
[20:43:34] -!- Deejay has quit [Quit: bye]
[20:43:36] <JT-Shop> boring bar would be too slow
[20:43:38] <Tom_itx> usually the local surplus guy has what i need
[20:43:49] <Tom_itx> yeah depends how many you plan to make
[20:43:56] <Tom_itx> one off i'd bore it
[20:44:00] <Tom_itx> 10k i'd drill
[20:44:26] <JT-Shop> I have 20 pcs to finish up
[20:44:39] <Tom_itx> it would be worth the drill i think
[20:45:06] <JT-Shop> yea, $50 for a S&D 63/64" but
[20:45:18] <JT-Shop> I don't have a boring head for the 308 anyway
[20:46:07] <Tom_itx> put that on your shopping list too
[20:47:17] -!- syyl [syyl!~sg@p200300632C3F1276B15D88C938624C36.dip0.t-ipconnect.de] has joined #linuxcnc
[20:48:42] -!- r0ute has quit [Ping timeout: 276 seconds]
[20:49:44] -!- syyl_ has quit [Ping timeout: 265 seconds]
[20:49:45] <JT-Shop> lol yea
[20:50:20] <JT-Shop> I have an el-cheapo boring head with a R8 shank I think
[20:51:16] <JT-Shop> oh it has a 1" straight shank too
[20:51:48] <Tom_itx> you're all set then
[20:52:58] <JT-Shop> I don't have a 1" BT30 holder only a kwik switch
[20:53:08] <Tom_itx> :(
[20:54:33] -!- sumpfralle has quit [Ping timeout: 245 seconds]
[20:54:39] -!- patrickarlt has quit [Ping timeout: 244 seconds]
[20:55:24] <JT-Shop> I'd have to get a TG100 collet holder to fit a 1" in the BT30
[20:55:35] <JT-Shop> bbl
[20:56:22] -!- SpeedEvil has quit [Quit: No Ping reply in 180 seconds.]
[20:57:08] -!- SpeedEvil [SpeedEvil!~quassel@tor/regular/SpeedEvil] has joined #linuxcnc
[21:03:07] -!- patricka_ has quit [Remote host closed the connection]
[21:05:28] -!- jerryitt has quit [Quit: Connection closed for inactivity]
[21:07:36] -!- Camaban has quit [Quit: Leaving]
[21:15:02] -!- chillly has quit [Quit: Ex-Chat]
[21:16:53] -!- SpeedEvil has quit [Quit: No Ping reply in 180 seconds.]
[21:17:42] -!- SpeedEvil [SpeedEvil!~quassel@tor/regular/SpeedEvil] has joined #linuxcnc
[21:19:07] -!- Akex has quit [Quit: Connection closed for inactivity]
[21:20:53] -!- Valen [Valen!~Valen@c211-30-128-202.blktn6.nsw.optusnet.com.au] has joined #linuxcnc
[21:23:00] -!- sumpfralle [sumpfralle!~lars@subaru.opennet-initiative.de] has joined #linuxcnc
[21:28:28] -!- gonzo_ [gonzo_!~gonzo_@host-92-14-209-118.as43234.net] has joined #linuxcnc
[21:34:32] -!- jvrousseau has quit [Quit: Textual IRC Client: www.textualapp.com]
[21:39:05] -!- acdha has quit [Quit: Textual IRC Client: www.textualapp.com]
[21:40:51] <furrywolf> argh. I hate medical care. I got an infection that I want to talk to a doctor about sooner rather than later. I go to the only local clinic. Their nearest appointment is THREE TO FOUR MONTHS. Apparantly their plan is to hope you get better or die.
[21:42:50] <LeelooMinai> There must be some quicker way...
[21:43:27] <furrywolf> yes, you shoot yourself. it's a much quicker way to kill yourself than the american health care system, although it'll do it eventually.
[21:44:20] <LeelooMinai> So what do you do if it's an infection dangerous to your life?
[21:44:34] <furrywolf> go to the emergency room and wait 6-24 hours.
[21:45:11] <LeelooMinai> Hmm, that's even worse than what I remember from Poland
[21:46:25] <LeelooMinai> Much worse in fact
[21:46:53] <furrywolf> yes. there's a reason people leave the US for health care.
[21:47:00] <furrywolf> did I mention it's also ungodly expensive?
[21:47:14] <cradek> furrywolf: where do you live?
[21:47:15] <furrywolf> a basic healthcare plan costs more than a full-time minimum wage job pays.
[21:47:21] <LeelooMinai> furrywolf: Move to Canada - it's not far away:)
[21:47:28] <furrywolf> cradek: far northern california
[21:47:53] <furrywolf> Obama promised affordable healthcare... instead it's just as expensive, but now you get fined for not being able to afford it.
[21:48:45] <cradek> furrywolf: weird. I live in a slightly-less-bad spot in the midwest and there are probably a dozen walk-in clinics I could get in still today, even if I didn't have insurance and a primary care doctor (which I do)
[21:49:19] <furrywolf> there's only one walk-in here, that's the open door clinic system... and they're booked for 3-4 months depending on location.
[21:49:20] <Cromaglious> la chatte du didn't like being combed out
[21:49:27] <cradek> it's totally untrue that obamacare made access to healthcare worse for poor people
[21:49:30] <LeelooMinai> Maybe that's US plan - to let the weak die off:)
[21:49:40] <Valen> I want one of these
https://www.youtube.com/watch?v=sFrVdoOhu1Q
[21:49:41] <furrywolf> there's an urgent care place next to the hospital, but it seems aimed at more-immediate issues.
[21:50:20] <cradek> "urgent care" are what they call ours too. they're good (and affordable) for stuff like getting stitches, getting a rx for a sinus infection, etc
[21:50:37] <cradek> maybe you should call that one up, or stop in and ask
[21:50:49] <Connor> cradek: I wouldn't have HealthCare if not for it right now.. My work offers HealthCare.. but, they're in a different City (Nashville vs Knoxville) and Only something called Blue Cross Blue Shield Select.. Which covers lots of Doctors in their area.. but hardly anything in mine..
[21:50:51] <Valen> infections become urgent rapidly, give em a call
[21:51:02] <furrywolf> cradek: have you looked at the price of health plans? they've gone up. a lot. obamacare mandated minimum services substantially above what a crappy discount healthy-person plan included, so they don't exist anymore.
[21:51:25] -!- f1oat4 has quit [Ping timeout: 250 seconds]
[21:51:36] <cradek> Connor: same for my gf. she couldn't afford it before, no way, and now she has a decent plan that she can pay for easily with the benefit
[21:51:47] <LeelooMinai> I somehow had an image of a huge person deressed as a trapper with 10 month beard and all stepping into a clinic.
[21:52:19] <Connor> One way they cut cost.. is to not have a ER co-pay. This forces people to goto their primary care doctor vs the ER for stupid sh!t.
[21:52:26] <cradek> Connor: umm ex-gf I mean (for reasons unlreated to obamacare) :-)
[21:52:40] <cradek> unrelated
[21:52:40] <cradek> jeez
[21:52:55] <LeelooMinai> unretarded
[21:53:08] <Connor> which I agree with.. just wish it didn't penalize pople like me who DO do that. I.E I had a Kidney stone a while back.. which a ER visit was appropriate for..
[21:54:03] <furrywolf> back before he was elected, I rather seem to remember the promise of a single universal health care system affordable to all.
[21:54:10] <cradek> furrywolf: quit bitching and go to the urgent care, we all care about you here, get going
[21:54:30] <furrywolf> instead we have the exact same system we had before, except it costs more, and you're fined if you can't afford it.
[21:54:33] <cradek> furrywolf: haha yeah it's obama's fault we don't have single-payer. in fact vote republican to show him you're mad
[21:54:54] <Connor> furrywolf: That was his "Goal".. But.. like everything in politics.. compromises had to be made.
[21:55:32] <furrywolf> I got a $325 fine on my taxes for not being able to afford $1300/month.
[21:55:38] <furrywolf> going to be $600 next year apparantly
[21:55:40] -!- mhaberler has quit [Quit: mhaberler]
[21:56:10] <Connor> 1300 a month ?
[21:56:15] <Connor> for just you?
[21:56:24] <furrywolf> yep
[21:56:31] <furrywolf> if you're self-employeed you get screwed
[21:56:36] <furrywolf> employed
[21:56:47] <furrywolf> none of the cheap options
[21:57:04] <Connor> I was self employeed.. Never paid that much..
[21:57:21] <Cromaglious> I'm thankful that I have VA and that counts as insurance
[21:57:40] <Connor> $734.82 for both me and the wife.. top tier coverage..
[21:57:41] <furrywolf> Connor: before or after obamacare? heh
[21:57:47] <Connor> BOTH.
[21:57:55] <furrywolf> $750 is still quite a bit more than I have spare.
[21:57:57] <cradek> actually $600/yr is a pretty decent tradeoff for the ability to get (the expensive) insurance with a pre-existing horrible condition in the future if you need it
[21:58:04] <Connor> We paid $1700 for a 3 person plan.
[21:58:05] <furrywolf> I still can't afford a mesa board for my mill... and that's only $200.
[21:58:21] <Connor> That's for 2 people.
[21:58:43] <Connor> What state are you In ?
[21:58:52] <furrywolf> california
[21:59:11] <furrywolf> and if I go give the urgent care place $200 (they're a lot more pricey than the clinic), I'm not buying a mesa board anytime soon.
[21:59:24] <Cromaglious> quit lying furry, you're in the state of Jefferson
[21:59:28] <furrywolf> (their website says a basic visit is $99 plus labwork)
[21:59:37] <furrywolf> Cromaglious: that failed, unfortunately.
[21:59:57] <Cromaglious> I'm in PRoC People Republic of California
[21:59:58] <Connor> what's you age and zipcode and annual household income ?
[22:00:11] <furrywolf> I can also just do what I've always done, and assume I'm not dying.
[22:00:36] -!- mhaberler [mhaberler!~mhaberler@193.228.47.221] has joined #linuxcnc
[22:00:53] <Connor> You can PM me if you don't want it public.
[22:01:48] <furrywolf> at least the intake form at the local clinic had a variety of boxes for non-binary genders.
[22:01:56] -!- patricka_ has quit [Read error: Connection reset by peer]
[22:01:56] -!- patrickarlt has quit [Ping timeout: 240 seconds]
[22:02:05] <furrywolf> healthcare has advanced. :)
[22:02:43] <DaViruz> suddenly socialist sweden don't seem so bad. you pay $30 for a visit, and that include any and all follow up visits
[22:02:58] <DaViruz> medication is capped at $150 or so a year, once you reach that it's free
[22:03:32] <cradek> when did socialist sweden seem bad?
[22:03:39] <furrywolf> lol
[22:03:57] <furrywolf> americans think all socialism is bad, despite the fact that capitalism will collapse without a bunch of it.
[22:04:18] <furrywolf> capitalism requires either socialism, communism, or lots of dead people.
[22:04:30] <DaViruz> cradek: when i look at my tax statements :(
[22:05:17] -!- messine has quit [Ping timeout: 250 seconds]
[22:05:34] <furrywolf> I paid something like 33% last year. when you're self-employeed, then get you double on a lot of them.
[22:06:14] <DaViruz> 33% is about what we pay being employed, though the employer has to pay a lot more on top of that
[22:06:47] <cradek> it's true the US self-employed tax hits are pretty bad
[22:06:58] <furrywolf> I didn't even bother looking at it this year... I just gave the tax preparer my numbers and let them give me a bill.
[22:07:18] <Connor> furrywolf: 30 year old, making 45k, in 90047 zipcode $299.00 per month ofr Silver Plan. $305 for a gold
[22:07:24] <cradek> DaViruz: and you get reasonable healthcare and peace? that's a bargain.
[22:07:36] <Connor> furrywolf:
http://www.coveredca.com/ go look up your costs..
[22:07:42] <DaViruz> cradek: yeah, i agree to be honest
[22:07:49] -!- __rob [__rob!~rob@5.80.64.6] has joined #linuxcnc
[22:08:06] <furrywolf> that's another benefit to sweden... when was the last time sweden invaded a foreign country just for the hell of it?
[22:08:36] <Connor> Granted, I made assumptions.. I have no idea how much you make, your age, or your zipcode.. but.. It would be rather hard to get to $1200 a month for healthcare.
[22:08:48] <cradek> and are you still arguing about gay people's rights? or women's for that matter?
[22:09:02] <furrywolf> I think the $1300/month was for a small business plan, that I could add my employee too for an additional cost.
[22:09:07] <furrywolf> s/too/to
[22:09:25] -!- _rob has quit [Ping timeout: 255 seconds]
[22:09:27] <LeelooMinai> furrywolf: They invaded Poland once...
[22:09:29] <Connor> You have to have a group for a small business.. which means 2 or more employees
[22:09:37] <furrywolf> everyone invades poland at least once.
[22:09:53] <DaViruz> furrywolf: 1600 circa i believe
[22:10:05] <LeelooMinai> Well, they did not last long at least:)
[22:10:26] <DaViruz> we did have some shady dealings with the nazis though
[22:10:42] <Connor> So, if it's just you.. the Affordable Care act is your best bet.. and till Oboma came along.. your WHERE screwed..
[22:14:43] <_methods> if those crazy japanese bastards hadn't attacked us we probably would have teamed up with the nazis
[22:14:54] <_methods> they kinda screwed adolf
[22:15:26] <LeelooMinai> Yes, because teaming up with nazis would be such a good thing
[22:15:47] <_methods> wtf is wrong with you
[22:15:51] <_methods> that would have been terrible
[22:16:01] <Valen> you were doing lendlease before japan attacked as I recall
[22:16:03] <_methods> you skin head
[22:17:00] <_methods> freakin canadian nazis
[22:17:21] <furrywolf> bbl, errands
[22:24:15] -!- per_sonne_ has quit [Ping timeout: 276 seconds]
[22:29:13] -!- patrick__ has quit [Remote host closed the connection]
[22:32:26] -!- KGB-linuxcnc has quit [Ping timeout: 264 seconds]
[22:34:07] -!- patrickarlt has quit [Read error: Connection reset by peer]
[22:40:27] <JT-Shop> I wonder what size pilot hole I need for the 63/64" bit and if I have enough HP to drill it lol
[22:40:48] -!- JohnyK has quit [Ping timeout: 245 seconds]
[22:40:56] <_methods> i'd step that one up
[22:41:36] <_methods> unless you got 20hp hehe
[22:41:41] <_methods> then punch it
[22:42:07] <_methods> you got through spindle coolant and insert drill
[22:42:09] <_methods> hehe
[22:52:51] -!- adb has quit [Ping timeout: 276 seconds]
[22:54:17] <JT-Shop> 7.5HP
[22:54:27] <JT-Shop> what kind of step would you take?
[22:55:15] -!- moorbo [moorbo!~moorbo@dyn-21-121.mdm.its.uni-kassel.de] has joined #linuxcnc
[22:58:43] -!- eventor has quit [Ping timeout: 252 seconds]
[22:59:41] -!- moorbo has quit [Ping timeout: 244 seconds]
[22:59:57] <_methods> heh whatever i could get away with
[23:00:02] <_methods> you got drill in a chuck?
[23:00:17] <_methods> i'd go as big as i could without drill slippin
[23:00:25] <_methods> how deep you drilling?
[23:00:51] <_methods> and you're tryin to get this hole to ream zone right?
[23:01:10] <_methods> does your machine have a tendency to overdrill dia on holes?
[23:02:57] -!- __rob has quit [Remote host closed the connection]
[23:02:58] <_methods> JT-Shop: flippin between computers
[23:03:16] -!- __rob [__rob!~rob@5.80.64.6] has joined #linuxcnc
[23:03:56] <_methods> having to compile freecad on my other linuxcnc box
[23:04:10] <_methods> for some reason freecad isn't in the wheezy repo
[23:13:39] -!- patricka_ has quit [Remote host closed the connection]
[23:15:56] <_methods> buckets'o'dependencies
[23:18:43] -!- patrickarlt has quit [Ping timeout: 255 seconds]
[23:23:24] -!- teepee has quit [Ping timeout: 276 seconds]
[23:23:24] teepee_ is now known as teepee
[23:31:17] -!- patrickarlt has quit [Remote host closed the connection]
[23:34:08] <Tom_itx> JT-Shop just drill it slow?
[23:34:13] -!- mhaberler has quit [Quit: mhaberler]
[23:34:27] <Tom_itx> or step from maybe 1/4 1/2 15/16
[23:36:45] -!- Tom_L [Tom_L!~Tom@ip68-102-196-57.ks.ok.cox.net] has joined #linuxcnc
[23:36:45] -!- Tom_L has quit [Changing host]
[23:36:45] -!- Tom_L [Tom_L!~Tom@unaffiliated/toml/x-013812] has joined #linuxcnc
[23:37:29] <Tom_L> http://tom-itx.no-ip.biz:81/~webpage/sumo_files/lathe1.jpg
[23:37:37] <Tom_L> that was 2 steps with 1/3 hp
[23:38:37] <Tom_L> http://tom-itx.no-ip.biz:81/~webpage/sumo_files/sumo_hub_motortube.jpg
[23:38:40] <Tom_L> the center tube
[23:39:09] <_methods> serxy
[23:39:59] -!- AR_ [AR_!~AR@24.238.81.234.res-cmts.sth2.ptd.net] has joined #linuxcnc
[23:43:06] -!- Tecan has quit [Quit: Live Long And Phosphor!]
[23:44:21] -!- Tom_L has quit [Read error: Connection reset by peer]
[23:44:41] -!- Tom_L [Tom_L!~Tom@unaffiliated/toml/x-013812] has joined #linuxcnc
[23:44:44] -!- Tom_L has quit [Read error: Connection reset by peer]
[23:45:03] <Tom_itx> haha, xchat doesn't like to change fonts
[23:45:04] -!- Tom_L [Tom_L!~Tom@ip68-102-196-57.ks.ok.cox.net] has joined #linuxcnc
[23:45:04] -!- Tom_L has quit [Changing host]
[23:45:04] -!- Tom_L [Tom_L!~Tom@unaffiliated/toml/x-013812] has joined #linuxcnc
[23:46:01] <_methods> oh yeah i guess i could install irc client on my other pc lol
[23:46:09] <_methods> i'm just so used to ssh into my irssi
[23:46:19] <Tom_itx> i've got one on every pc
[23:46:26] <Tom_itx> running out of nics :)
[23:46:34] <_methods> hehe
[23:55:45] -!- The_Ball [The_Ball!~ballen@c114-77-179-73.hillc3.qld.optusnet.com.au] has joined #linuxcnc
[23:58:28] -!- The_Ball has quit [Remote host closed the connection]
[23:59:46] <Valen> Tom_itx: why not use one of those irc forwarder things?
