Back
[00:03:48] <tjtr33> chopper79, if i read correctly, the logic is to inhibit the leading joint when it hits the switch, but allow the 2nd joint to catch up, till both are 'just' at the trip points
[00:06:21] <tjtr33> the same logic might be done by incrementally moving a small unit of distance ( not a step, but a small unit of measurable distance ) in a loop till 1st then 2nd are at the switch points
[00:06:59] <tjtr33> then back 'em off and repeat with smaller distances, then set machine 0
[00:07:45] <tjtr33> ( measure twice, zero once :)
[00:10:00] -!- fatpandas has quit [Quit: leaving]
[00:11:27] <tjtr33> you wont make it work with the same nets and comps, you will make it work with same idea. an 'event' of the 1st swx change will inhibit the 1st joints motion, yet allow the 2nd join to seek its switch
[00:11:41] <tjtr33> same idea, different nets and comps
[00:12:53] -!- fatpandas [fatpandas!~fatpandas@c-76-105-103-177.hsd1.ga.comcast.net] has joined #linuxcnc
[00:18:03] <chopper79> tjtr33.... You did read that correctly.
[00:20:10] <Jymmm> JT-Shop: I don't see where the cnc attachment is for your log splitter? No sense and detect potantial canidates, laser guided splittting for the maximum yield, the robotic arm that picks up and un/loads the splitter?
[00:20:42] <JT-Shop> http://www.youtube.com/watch?v=cUf4F9VXo_s
[00:20:57] <JT-Shop> well im not done yet
[00:21:12] <Jymmm> good song
[00:21:48] <Jymmm> ah, ok. Dont forget the roving patrol attack splitter feature
[00:22:23] <Jymmm> cracking trespasser's skulls since 2013
[00:25:59] <JT-Shop> http://www.youtube.com/watch?v=Ixqbc7X2NQY
[00:26:04] <Jymmm> JT-Shop:
http://ultimatefandango.com/groovers/02 Spooky _ Classics IV.mp3
[00:26:08] <Jymmm> doh
[00:27:47] <Jymmm> JT-Shop:
http://ultimatefandango.com/groovers/02 Spooky%20_%20Classics IV.mp3
[00:27:54] <Jymmm> damn
[00:28:13] <Jymmm> JT-Shop:
http://ultimatefandango.com/groovers/02%20Spooky%20_%20Classics%20IV.mp3
[00:28:25] <Jymmm> there we go
[00:29:16] <Jymmm> JT-Shop: OH, did you see the cone log splitter???
[00:29:34] <JT-Shop> yea
[00:29:57] <JT-Shop> now some Nena
[00:29:57] <Jymmm> JT-Shop: it worked so well too surprisngly
[00:30:13] <Tom_itx> works like a big wood screw
[00:30:21] <Jymmm> http://www.youtube.com/watch?v=M1Cz5G56J-s
[00:30:43] <Jymmm> but it doens't throw pieces around is the part I like
[00:30:44] <Tom_itx> JT-Shop, how's your splitter coming?
[00:30:56] <Tom_itx> JT-Shop, are you getting any weather yet?
[00:31:13] <Tom_itx> we're supposed to get a big winter storm starting tomorrow
[00:31:26] <JT-Shop> not yet
[00:31:43] <Tom_itx> changed the mag in the snow blower just in case
[00:31:49] <Tom_itx> wasn't gettin any spark
[00:32:21] <Jymmm> here's another one...
http://www.youtube.com/watch?v=Br044PKw-QE
[00:32:28] <JT-Shop> http://forecast.weather.gov/MapClick.php?lat=36.7378524&lon=-90.48799159999999&site=all&smap=1&searchresult=Poplar%20Bluff%2C%20MO%2063901%2C%20USA
[00:33:32] <Tom_itx> you may be on the edge of it
[00:34:32] -!- jensor [jensor!47b37591@gateway/web/freenode/ip.71.179.117.145] has joined #linuxcnc
[00:36:00] -!- jensor has quit [Client Quit]
[00:36:10] <Jymmm> The gal is pretty good, but man the whining that splitter is making is just eery
http://www.youtube.com/watch?v=M1eIgBZqeY0
[00:39:39] <Jymmm> JT-Shop: DONT TRY THIS AT HOME
http://www.youtube.com/watch?v=HPWaTaKoMqU&NR=1&feature=endscreen
[00:40:25] <JT-Shop> http://www.youtube.com/watch?v=7fWo0P0MdJM
[00:42:08] <Jymmm> no way thats real
[00:42:15] <JT-Shop> yea
[00:42:23] <tjtr33> the ax is 'flicked' , thats why it looks as if she slapped it sometimes
[00:42:44] <Jymmm> crazyglued or something
[00:42:48] <JT-Shop> there is two ways to split with a double bit axe, the flick or the angle
[00:43:12] <JT-Shop> straight grain wood splits easy if you know how
[00:43:27] <Jymmm> and seasoned for 5 years =)
[00:43:42] <JT-Shop> if you watch the axe it is horz at the end
[00:44:09] <Jymmm> I saw that, that's what made me think it's fake
[00:45:25] <JT-Shop> no trick it is a way to split, I was taught that way when I was 15
[00:45:38] <Jymmm> I stil think I like the tire screw splitter.... any car, anywhere, no hassel
[00:45:47] <tjtr33> thats the flick, a twist right after contact, dont try to go thru
[00:47:03] <tjtr33> shes good even if its well dried
[00:47:21] <Jymmm> floor jack, 4-way tire iron, the screw splitter and you're good to go.
[00:47:49] <Jymmm> bonus is 1/4" plywood shield to save the paint job
[00:48:51] <Jymmm> I wonder how much HP would be needed w/o a car?
[00:49:53] <Jymmm> JT-Shop: I think you already saw the wood gas heater
[00:50:34] <nevyn> I used to have to split redgum for kindling.
[00:50:47] <nevyn> I was very careful which block from the stack I selected
[00:50:57] <Jymmm> redgum?
[00:50:57] <nevyn> no knots or branches nice straight grain.
[00:51:13] <Jymmm> ah
[00:51:21] -!- rob_h has quit [Ping timeout: 276 seconds]
[00:51:25] <Jymmm> why so selective?
[00:51:58] <nevyn> because I was splitting it by hand with a blocksplitter.
[00:52:03] -!- MVCalypso has quit [Ping timeout: 260 seconds]
[00:52:08] <Jymmm> and?
[00:52:15] <nevyn> to turn something the size of a breadbox into 1/4 inch sticks
[00:52:34] <Jymmm> oh, maye you need this then
http://www.youtube.com/watch?v=HPWaTaKoMqU&NR=1&feature=endscreen
[00:53:09] <Jymmm> seems that would make great safe kindling
[00:53:18] <Jymmm> little effort and still have your fingers
[00:55:07] <Jymmm> Eeeesh
http://www.youtube.com/watch?v=37gH9SObKVA&feature=endscreen&NR=1
[00:56:58] -!- Nick001-Shop has quit [Remote host closed the connection]
[00:59:44] <Jymmm> JT-Shop: AH HA! NOW I know why the reenforcment,,, it's a tractor attachment...
http://www.youtube.com/watch?v=GAdWb9pdZNw
[01:00:59] -!- tayy has quit [Remote host closed the connection]
[01:02:24] * JT-Shop goes inside now
[01:02:40] <Jymmm> laters gracie
[01:02:42] <JT-Shop> say goodnight Gracie
[01:02:47] <Jymmm> ;)
[01:02:58] <r00t4rd3d> wow, Android for routers now like ddwrt/openwrt
[01:02:59] <r00t4rd3d> http://www.droidifi.com/
[01:06:18] -!- asdfasd has quit [Ping timeout: 276 seconds]
[01:06:29] <Valen> networking seems to not be big on the android features list
[01:07:17] -!- hdokes has quit [Ping timeout: 252 seconds]
[01:09:12] -!- chopper79 has quit [Quit: Leaving.]
[01:12:44] <Jymmm> lathe log splitter
http://www.youtube.com/watch?v=QMkL6UQp2fY&NR=1&feature=endscreen
[01:15:05] -!- tmcw has quit [Remote host closed the connection]
[01:17:01] <Jymmm> Redneck log splitter (ouch)
http://www.youtube.com/watch?v=40sCGb678sQ&NR=1
[01:22:53] <nevyn> Jymmm: I still like this one:
http://www.youtube.com/watch?v=hhmKBDIAXd0
[01:29:50] -!- L33TG33KG34R has quit [Read error: Connection reset by peer]
[01:30:13] -!- L33TG33KG34R [L33TG33KG34R!~L33TG33KG@S010674ea3aa162f7.cg.shawcable.net] has joined #linuxcnc
[01:31:55] <nevyn> Jymmm: this is also interesting :
http://www.youtube.com/watch?v=_olacH1hlWg
[01:41:13] -!- jmkelly_ has quit [Client Quit]
[01:43:49] <Jymmm> Fastest Firewoood Splitter in the world!
http://www.youtube.com/watch?v=5pLiJMZjQDw&feature=related
[01:45:51] <nevyn> Jymmm: I think the others I had were faster
[01:46:05] <Jymmm> haven't got there yet =)
[01:46:07] <nevyn> the on that took a 6' round and split it in a single shot
[01:46:18] <Jymmm> whats the tumbler for?
[01:46:50] <nevyn> http://www.youtube.com/watch?v=XAqi6Zb_c6E
[01:46:57] -!- Gene34 has quit []
[01:47:03] <Jymmm> the 1st is cool
[01:47:10] <nevyn> Jymmm: desplinter
[01:47:22] <Jymmm> ah
[01:47:28] <Jymmm> starting 2nd now
[01:47:29] <nevyn> it drops all the kindling bits out
[01:47:36] <Jymmm> nice
[01:48:47] <Jymmm> ah, like the green one I showed earlier. I like it too
[01:51:20] <Jymmm> nevyn: I like the first one the best, looked trailer portable too
[01:51:41] -!- nOStahl has quit [Quit: nOStahl]
[01:51:51] <Jymmm> free kindling and sawdust for the garden =)
[01:52:37] <Jymmm> Though large redwood bark chips work best for weed control.
[01:52:41] <nevyn> the bit I don't get is what the cost/benefit is..
[01:52:58] <Jymmm> how so?
[01:53:09] <nevyn> so we would burn ~ 8m3 of firewood a year in a 40square house
[01:53:28] <nevyn> that's about 4hrs work for any of those big machines
[01:53:52] <nevyn> it was only a weekend work for 3 men and a simple axial splitter.
[01:54:09] <Jymmm> Ah, well think of this... you have the forest, bring that gut in for say $300 and have him do all that for you in a few hours.
[01:54:34] <nevyn> so it becomes a hire in the machine + guy problem.
[01:54:44] <nevyn> which might be worthwhile
[01:55:05] <nevyn> I suspect we did hire someone in to cut the rounds...
[01:55:11] <Jymmm> yeah, especially in certain areas of the country
[01:56:23] <Jymmm> cut and split all at once, sounds like a good deal to me
[01:56:56] <nevyn> so everything I've seen these guys splitting seems.. light
[01:57:06] <nevyn> and crappy.
[01:58:36] <Jymmm> Yeah, I really wouldn't know. I have touch/thought of splitting firewood in eons
[01:58:42] <Jymmm> except for camping
[01:58:49] <nevyn> http://www.gumtree.com.au/s-ad/bellevue-heights/miscellaneous-goods/firewood-river-redgum/1013332339
[01:58:53] <ReadError> 3060 extrusion is much larger than expected ;o
[02:00:16] <jdh> is it 30 by 60?
[02:01:19] <ReadError> 3"x6X
[02:01:22] <ReadError> 6"*
[02:01:59] <nevyn> hrm that's bigger than I would have thought
[02:02:54] <ReadError> yea its a very stout piece of aluminum
[02:05:20] * nevyn would have thought mm not "
[02:05:37] <nevyn> as in millimeters not mils
[02:07:35] -!- Wildhoney has quit [Ping timeout: 255 seconds]
[02:08:05] <ReadError> its maybe 40-50lbs
[02:08:16] <ReadError> 4' long i think
[02:09:29] <nevyn> heh
[02:09:41] -!- pikeaero has quit [Remote host closed the connection]
[02:09:43] -!- tmcw has quit [Remote host closed the connection]
[02:10:16] -!- danielfalck has quit [Ping timeout: 256 seconds]
[02:12:06] -!- adb has quit [Ping timeout: 264 seconds]
[02:20:36] -!- pikeaero [pikeaero!~quassel@216-167-252-197.eastlink.ca] has joined #linuxcnc
[02:21:02] -!- jfire has quit [Quit: Leaving.]
[02:21:06] <Jymmm> nevyn: cut, feed, split, de-kindle, all sounds good to me
[02:21:17] <Jymmm> and pile too =)
[02:22:25] <Jymmm> nevyn: maybe for an extra $40 there might be a stacker option too =)
[02:23:38] <tjtr33> the short stroke hydraulic splitters, like a cyclical hammer blow... if the end of stroke had a twist - you get the barefoot girl's flick.
[02:27:28] -!- pjm has quit [Ping timeout: 252 seconds]
[02:29:28] -!- wboykinm has quit [Remote host closed the connection]
[02:30:33] -!- pjm [pjm!~pjm@uhfsatcom.plus.com] has joined #linuxcnc
[02:32:20] -!- JT-Shop has quit [Ping timeout: 255 seconds]
[02:32:21] -!- jthornton has quit [Ping timeout: 255 seconds]
[02:32:29] -!- jthornton_ [jthornton_!~john@184-63-140-99.cust.wildblue.net] has joined #linuxcnc
[02:32:36] -!- JT-Shop-2 [JT-Shop-2!~John@184-63-140-99.cust.wildblue.net] has joined #linuxcnc
[02:35:49] -!- JT-Shop-2 has quit [Read error: Connection reset by peer]
[02:35:49] -!- jthornton_ has quit [Read error: Connection reset by peer]
[02:37:30] -!- JT-Shop-2 [JT-Shop-2!~John@184-63-140-99.cust.wildblue.net] has joined #linuxcnc
[02:37:31] -!- jthornton_ [jthornton_!~john@184-63-140-99.cust.wildblue.net] has joined #linuxcnc
[02:44:34] <AR__> so after building my mill
[02:44:41] <AR__> i realize it's a piece of shit
[02:44:49] <AR__> i dont even know what to make with it now
[02:44:58] <Valen> lol
[02:45:13] <AR__> i really had no reason to build it other than an obsession with wanting it
[02:45:29] <AR__> oh well
[02:45:57] <cradek> well then the obvious thing to do now is build a better one
[02:47:41] -!- cmorley1 has quit [Ping timeout: 256 seconds]
[02:47:57] -!- cmorley [cmorley!~chris@S010600c09fc019c2.no.shawcable.net] has joined #linuxcnc
[02:49:31] <AR__> omg
[02:51:41] <AR__> that was kindof my plan until i went over budget to build this one
[02:54:40] <Valen> whats not good about it?\
[02:57:11] <skunkworks> actually - the obvious thing is to buy a old cnc with a dead control :)
[02:57:12] <ReadError> improve on it
[02:57:26] <ReadError> r00t4rd3d's was made of MDF
[02:57:31] <ReadError> now he has it all riced up
[03:11:54] <r00t4rd3d> AR__, why is it a pos?
[03:12:35] <AR__> i dunno
[03:12:54] <AR__> just cause i'm tired of looking at it i guess
[03:13:39] <nevyn> skunkworks: just make sure that there's not too much slop in the spindle bearings...
[03:13:46] <nevyn> most other things are fixable ;)
[03:15:00] <r00t4rd3d> ar cant you get it to work ?
[03:15:39] -!- pikeaero has quit [Remote host closed the connection]
[03:17:10] -!- Valen has quit [Read error: No route to host]
[03:17:57] <r00t4rd3d> AR__
[03:17:57] -!- Valen [Valen!~Valen@c211-30-129-65.blktn6.nsw.optusnet.com.au] has joined #linuxcnc
[03:18:05] <AR__> ?
[03:18:09] <AR__> nah it works fine
[03:22:48] -!- joe9 has quit [Quit: leaving]
[03:46:00] <abetusk> is there a language specification for g-code somewhere?
[03:47:02] -!- dhoovie [dhoovie!~kvirc@122.177.154.147] has joined #linuxcnc
[03:50:04] -!- nOStahl has quit [Quit: nOStahl]
[03:52:02] <Tom_itx> for linuxcnc or in general?
[03:58:29] <Tom_itx> http://technisoftdirect.com/catalog/download/RS274NGC_3.pdf
[04:04:12] -!- gene_ has quit [Remote host closed the connection]
[04:04:17] <mrsun_> hmm using the cnc mill to grind single point gear cutters maybe :P
[04:04:36] <mrsun_> just program the cutting path with extremly light cuts and grind them ? :P
[04:04:37] -!- gene_ [gene_!~gene@204.111.64.149] has joined #linuxcnc
[04:04:42] <mrsun_> think that would be possible ?
[04:05:02] <mrsun_> maybe hard to tell how much material it will actualy take of per pass when grinding ?
[04:07:06] <abetusk> Tom_itx, thanks
[04:07:12] -!- tjb1 has quit [Quit: tjb1]
[04:09:27] -!- chopper79 [chopper79!~Jeremy@173-15-98-106-Illinois.hfc.comcastbusiness.net] has joined #linuxcnc
[04:13:35] -!- sumpfralle has quit [Ping timeout: 260 seconds]
[04:13:54] -!- chopper79 has quit [Ping timeout: 264 seconds]
[04:15:31] -!- mikegg has quit [Ping timeout: 260 seconds]
[04:44:06] <Tecan> finally! linux games on steam...
http://i.imgur.com/xuJdgYn.jpg
[04:44:20] <Tecan> they run well too
[04:44:31] <Tecan> sales on today for them
[04:44:47] <Valen> interesting
[04:45:08] <Valen> do games i have in windows that are now linuxy carry over?
[04:46:32] <Tecan> yes
[04:46:37] <Valen> handy
[04:47:33] <Valen> productivity reduction imminent
[04:47:51] <Valen> rofl
[04:47:52] <Valen> or not
[04:47:58] <Valen> 175mb to install steam
[04:55:13] <Tecan> hehe
[04:55:59] -!- Valen has quit [Remote host closed the connection]
[04:58:18] -!- emacsen has quit [Ping timeout: 264 seconds]
[05:00:48] <tjtr33> abetusk:
http://code.google.com/p/rs274ngc/ for the vrsn used in linuxcnc, others use rs274 and rs274x
[05:01:25] -!- danielfalck [danielfalck!~danielfal@static-50-53-1-104.bvtn.or.frontiernet.net] has joined #linuxcnc
[05:03:42] -!- jfire has quit [Quit: Leaving.]
[05:04:46] <abetusk> sorry for my ignorance, but what does the code do? Is there any documentation, other than the source?
[05:05:11] <tjtr33> danielfalck, i used FreeCad again today, very nice
[05:06:23] <tjtr33> abetusk, it describes the path for a tool to move along ( and velocities and machne tool function like flush and in general, the things you'd do by hand, but very explicitly)
[05:07:37] <abetusk> I'm still unclear as to what this program's (or library's?) function is
[05:07:53] <tjtr33> abetusk, for a simple overview , there's the gcode reference in linuxcnc, its on the main desktop menu 'Linuxcnc G-Code Quick Reference'
[05:08:40] <abetusk> it sends out stepper driver signals over the parallel port? How does it "interpret" g-code? What does it interpret it to?
[05:09:50] <tjtr33> no, gcode is not that low level, its like driving instructions, start in CHicago, turn left 3 miles, stop, take lunch, go north 3days... like that
[05:10:04] <abetusk> I understand that.
[05:10:08] <tjtr33> the stepper signal are way below that level,
[05:10:15] <abetusk> So what is this program doing?
[05:10:55] <tjtr33> this program? what do you mean? linuxcnc?
[05:11:47] <abetusk> rs247ngc. I just compiled it using the Makefile provided and it created canon.o. What is canon.o? Is this a library of some sort?
[05:11:55] <abetusk> the link you provided
[05:12:50] <tjtr33> rs274ngc is not a program, it is a language. linuxcnc reads that language and coordinates machine functions and motion to accomplish the task described by the language
[05:13:22] <tjtr33> you say what you want in rs274ngc, linuxcnc executes your commands
[05:14:00] <abetusk> I feel like we're running around in circles. Anyway, the spec. there was the one Tom_itx already provided, but thanks anyway.
[05:16:25] <tjtr33> look at the diagram in section 4 of
http://www.linuxcnc.org/docs/html/code/Code_Notes.html
[05:17:59] -!- dhoovie has quit [Read error: Connection reset by peer]
[05:18:27] -!- dhoovie [dhoovie!~kvirc@122.177.154.147] has joined #linuxcnc
[05:22:10] -!- dhoovie has quit [Read error: Connection reset by peer]
[05:22:37] -!- dhoovie [dhoovie!~kvirc@122.177.154.147] has joined #linuxcnc
[05:24:51] <tjtr33> danielfalck,
http://imagebin.org/247376 i learned not to chamfer incomplete hole edges, where they might be cliped by another chamfer :) nice app thx!
[05:41:44] -!- tjb1-mobile [tjb1-mobile!~tjb1-mobi@74.43.50.189] has joined #linuxcnc
[05:44:10] -!- dhoovie has quit [Ping timeout: 246 seconds]
[05:47:42] AR__ is now known as AR_
[05:49:44] <AR_> which hole edges
[05:50:43] -!- danielfalck has quit [Ping timeout: 260 seconds]
[06:02:05] -!- Fox_Muldr has quit [Ping timeout: 260 seconds]
[06:03:49] -!- Fox_Muldr [Fox_Muldr!quakeman@frnk-5f746e65.pool.mediaWays.net] has joined #linuxcnc
[06:06:38] -!- kwallace1 [kwallace1!~kwallace@tmb-250.sonnet.com] has parted #linuxcnc
[06:07:31] <tjtr33> where a hole chamfer would intersect the block edge chamfer, say a hole that was 1mm from block edge, but block already had a 1mm chamfer.
[06:07:32] <tjtr33> if i try to chamfer the hole, then (on my syste) FreeCad will dissappear ( blowed up real good).
[06:07:55] <AR_> oh
[06:07:55] <AR_> yeah
[06:07:56] <tjtr33> i can make that error repeat , so i dont do that now
[06:08:17] <AR_> lol
[06:08:22] <tjtr33> :)
[06:08:25] <tjtr33> gn8
[06:08:31] -!- tjtr33 [tjtr33!~tomp@76-216-189-23.lightspeed.cicril.sbcglobal.net] has parted #linuxcnc
[06:15:41] -!- jmkelly has quit [Quit: ChatZilla 0.9.90 [Firefox 18.0.2/20130201065344]]
[06:21:50] -!- cmorley1 [cmorley1!~chris@S010600c09fc019c2.no.shawcable.net] has joined #linuxcnc
[06:24:33] -!- cmorley has quit [Ping timeout: 248 seconds]
[06:25:46] -!- zzolo has quit [Quit: zzolo]
[06:31:05] -!- cmorley [cmorley!~chris@S010600c09fc019c2.no.shawcable.net] has joined #linuxcnc
[06:32:26] -!- User982 [User982!31b0c147@gateway/web/freenode/ip.49.176.193.71] has joined #linuxcnc
[06:32:43] -!- User982 [User982!31b0c147@gateway/web/freenode/ip.49.176.193.71] has parted #linuxcnc
[06:34:33] -!- cmorley1 has quit [Ping timeout: 276 seconds]
[06:37:28] -!- tjb1-mobile has quit [Read error: Connection reset by peer]
[06:44:13] -!- mhaberler [mhaberler!~mhaberler@macbook.stiwoll.mah.priv.at] has joined #linuxcnc
[06:49:54] -!- mhaberler has quit [Ping timeout: 264 seconds]
[06:50:43] -!- AR_ has quit [Ping timeout: 248 seconds]
[06:58:46] -!- jfire has quit [Quit: Leaving.]
[07:25:32] -!- asdfasd [asdfasd!grgrgrgrg@149.241.132.117] has joined #linuxcnc
[07:27:06] -!- mhaberler [mhaberler!~mhaberler@089144206234.atnat0015.highway.a1.net] has joined #linuxcnc
[07:41:39] -!- Youdaman has quit []
[07:47:11] -!- mhaberler has quit [Read error: Connection reset by peer]
[07:47:54] -!- halo_cast [halo_cast!~halo_cast@p549F7F07.dip.t-dialin.net] has joined #linuxcnc
[07:50:37] -!- emel has quit [Excess Flood]
[07:53:44] -!- DJ9DJ [DJ9DJ!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[07:54:01] <DJ9DJ> moin
[08:08:31] -!- halo_cast has quit [Ping timeout: 256 seconds]
[08:10:02] -!- mhaberler [mhaberler!~mhaberler@089144206234.atnat0015.highway.a1.net] has joined #linuxcnc
[08:23:42] -!- halo_cast [halo_cast!~halo_cast@p549F7F07.dip.t-dialin.net] has joined #linuxcnc
[08:24:11] <Loetmichel> mornin'
[08:24:20] -!- holst [holst!~rasmus@h196.natout.aau.dk] has joined #linuxcnc
[08:43:21] <Jymmm> Yep it's 0043
[08:43:52] <Jymmm> Loetmichel: How ya doin for a Friday
[08:51:38] -!- mhaberler has quit [Read error: Connection reset by peer]
[08:52:16] -!- mhaberler [mhaberler!~mhaberler@089144206234.atnat0015.highway.a1.net] has joined #linuxcnc
[08:54:31] -!- V0idExp [V0idExp!~v0idexp@151.22.102.42] has joined #linuxcnc
[08:57:32] -!- mhaberler has quit [Read error: Connection reset by peer]
[08:58:00] -!- mhaberler [mhaberler!~mhaberler@089144206234.atnat0015.highway.a1.net] has joined #linuxcnc
[09:00:34] <Loetmichel> friday?
[09:00:46] <Loetmichel> do you hjave a time machine?
[09:00:59] <Loetmichel> its wenedsday over here
[09:01:25] <Jymmm> it's always friday in some parallel universe
[09:02:38] -!- rob_h [rob_h!~rob_h@5e0473f7.bb.sky.com] has joined #linuxcnc
[09:03:05] -!- mhaberler has quit [Ping timeout: 240 seconds]
[09:03:25] <Jymmm> ... and saturday, and sunday, and...
[09:05:10] <Jymmm> Kimchi NOT
http://www.youtube.com/watch?v=lfJETqgWNK4&
[09:19:59] -!- adb [adb!~IonMoldov@178.211.237.94] has joined #linuxcnc
[09:20:02] -!- halo_cast has quit [Quit: Nettalk6 - www.ntalk.de]
[09:20:18] -!- halo_cast [halo_cast!~halo_cast@p549F7F07.dip.t-dialin.net] has joined #linuxcnc
[09:27:54] -!- mhaberler [mhaberler!~mhaberler@089144206234.atnat0015.highway.a1.net] has joined #linuxcnc
[09:50:32] -!- mhaberler has quit [Quit: mhaberler]
[09:50:55] -!- racycle has quit [Quit: racycle]
[10:08:46] -!- Thetawaves has quit [Remote host closed the connection]
[10:09:52] -!- Thetawaves [Thetawaves!~theta@7-139-42-72.gci.net] has joined #linuxcnc
[10:33:23] -!- psha[work] [psha[work]!~psha@195.135.238.205] has joined #linuxcnc
[10:33:38] -!- b_b has quit [Changing host]
[10:35:30] -!- mhaberler [mhaberler!~mhaberler@188-23-195-10.adsl.highway.telekom.at] has joined #linuxcnc
[10:36:57] -!- Thetawaves has quit [Quit: Leaving]
[10:37:20] -!- Thetawaves [Thetawaves!~theta@7-139-42-72.gci.net] has joined #linuxcnc
[10:41:26] -!- halo_cast has quit [Ping timeout: 244 seconds]
[10:43:34] -!- cncbasher__ has quit [Quit: time to make some more scrap]
[10:43:52] -!- cncbasher has quit [Remote host closed the connection]
[10:43:54] -!- cncbasher_ has quit [Read error: Connection reset by peer]
[10:47:06] -!- mhaberler has quit [Quit: mhaberler]
[10:47:54] -!- halo_cast [halo_cast!~halo_cast@p549F7F07.dip.t-dialin.net] has joined #linuxcnc
[10:55:53] -!- The_Ball has quit [Ping timeout: 256 seconds]
[10:58:03] -!- racycle has quit [Quit: racycle]
[11:02:43] -!- tayy has quit [Remote host closed the connection]
[11:04:50] -!- mackerski has quit [Ping timeout: 260 seconds]
[11:04:50] mackerski_ is now known as mackerski
[11:07:29] -!- V0idExp1 [V0idExp1!~v0idexp@151.22.102.42] has joined #linuxcnc
[11:07:29] -!- V0idExp has quit [Read error: Connection reset by peer]
[11:13:12] -!- cncbasher [cncbasher!~quassel@cpc15-hart9-2-0-cust101.11-3.cable.virginmedia.com] has joined #linuxcnc
[11:14:23] -!- vladimirek [vladimirek!~vladimire@95.105.250.72] has joined #linuxcnc
[11:20:06] -!- bootnecklad [bootnecklad!~bootneckl@host-78-151-51-90.as13285.net] has joined #linuxcnc
[11:20:38] -!- bootnecklad has quit [Client Quit]
[11:22:06] -!- The_Ball [The_Ball!~The_Ball@122.150.108.38] has joined #linuxcnc
[11:27:56] -!- The_Ball has quit [Ping timeout: 255 seconds]
[11:29:22] -!- V0idExp [V0idExp!~v0idexp@37.100.252.84] has joined #linuxcnc
[11:31:05] -!- V0idExp1 has quit [Read error: No route to host]
[11:31:13] -!- V0idExp1 [V0idExp1!~v0idexp@151.22.102.42] has joined #linuxcnc
[11:31:22] -!- V0idExp1 has quit [Client Quit]
[11:31:40] -!- V0idExp1 [V0idExp1!~v0idexp@151.22.102.42] has joined #linuxcnc
[11:34:50] -!- V0idExp has quit [Ping timeout: 257 seconds]
[11:37:36] -!- syyl_ws [syyl_ws!~sg@p4FD1318F.dip.t-dialin.net] has joined #linuxcnc
[11:40:25] -!- syyl_ws_ [syyl_ws_!~sg@p4FD139DC.dip.t-dialin.net] has joined #linuxcnc
[11:40:29] -!- syyl_ [syyl_!~syyl@p4FD139DC.dip.t-dialin.net] has joined #linuxcnc
[11:43:20] -!- syyl has quit [Ping timeout: 256 seconds]
[11:43:30] -!- syyl_ws has quit [Ping timeout: 252 seconds]
[11:45:54] -!- tchui341 has quit [Ping timeout: 276 seconds]
[11:47:31] -!- skunkworks has quit [Remote host closed the connection]
[11:56:12] -!- V0idExp1 has quit [Quit: Leaving.]
[11:57:38] -!- V0idExp [V0idExp!~v0idexp@151.22.102.42] has joined #linuxcnc
[12:02:56] -!- tayy has quit [Remote host closed the connection]
[12:04:30] jthornton_ is now known as jthornton
[12:16:22] -!- mikegg [mikegg!~Mike@c-98-194-206-104.hsd1.tx.comcast.net] has joined #linuxcnc
[12:30:56] -!- dway has quit [Client Quit]
[12:32:23] -!- shdhdfghd [shdhdfghd!grgrgrgrg@149.241.132.117] has joined #linuxcnc
[12:33:32] -!- asdfasd has quit [Ping timeout: 255 seconds]
[12:57:18] -!- The_Ball [The_Ball!~The_Ball@122.150.108.38] has joined #linuxcnc
[12:57:31] -!- servos4ever [servos4ever!~chatzilla@173-87-50-96.dr01.hnvr.mi.frontiernet.net] has joined #linuxcnc
[13:13:39] -!- mikegg has quit [Ping timeout: 248 seconds]
[13:16:04] -!- syyl_ws_ has quit [Quit: Verlassend]
[13:23:38] -!- chopper79 [chopper79!~Jeremy@66.94.201.202] has joined #linuxcnc
[13:55:15] -!- holst has quit [Ping timeout: 248 seconds]
[13:56:20] -!- TwisteR [TwisteR!~TwisteR@94.158.72.67] has joined #linuxcnc
[13:56:44] <TwisteR> hi all!
[13:57:09] <TwisteR> any Gentoo users out there?
[13:58:51] <TwisteR> I need some tips on proper combination of kernel version & RTAI CVS revision
[14:00:06] <TwisteR> as porting RTAI to 3.x in process right now and I can't build it at the moment
[14:01:05] -!- mackerski has quit [Ping timeout: 248 seconds]
[14:01:05] mackerski_ is now known as mackerski
[14:04:10] -!- FABRIZIO has quit [Quit: Page closed]
[14:04:26] -!- FinboySlick [FinboySlick!~shark@74.117.40.10] has joined #linuxcnc
[14:06:34] shdhdfghd is now known as asdfasd
[14:08:42] -!- V0idExp has quit [Quit: Leaving.]
[14:08:54] <TwisteR> asdfasd, cleaning up your keyboard? :)
[14:11:36] -!- chopper79 has quit [Quit: Leaving.]
[14:13:21] -!- V0idExp [V0idExp!~v0idexp@151.22.102.42] has joined #linuxcnc
[14:13:27] -!- mhaberler [mhaberler!~mhaberler@194-166-32-48.adsl.highway.telekom.at] has joined #linuxcnc
[14:19:13] -!- halo_cast has quit [Ping timeout: 248 seconds]
[14:25:11] -!- crib has quit [Quit: quit]
[14:30:22] -!- chillly has quit [Quit: Leaving]
[14:31:32] -!- AR_ [AR_!~AR@24.115.215.149] has joined #linuxcnc
[14:39:01] -!- mackerski has quit [Quit: mackerski]
[14:40:35] -!- chopper79 [chopper79!~Jeremy@66.94.201.202] has joined #linuxcnc
[14:43:00] -!- joe9 [joe9!~joe9@c-24-98-97-215.hsd1.ga.comcast.net] has joined #linuxcnc
[14:46:58] -!- ravenlock [ravenlock!~ravenlock@enlightenment/developer/ravenlock] has joined #linuxcnc
[14:53:33] -!- plc5_250 [plc5_250!4622ae44@gateway/web/freenode/ip.70.34.174.68] has joined #linuxcnc
[14:53:39] -!- plc5_250 [plc5_250!4622ae44@gateway/web/freenode/ip.70.34.174.68] has parted #linuxcnc
[14:54:50] -!- plc5_250 [plc5_250!4622ae44@gateway/web/freenode/ip.70.34.174.68] has joined #linuxcnc
[14:54:56] -!- plc5_250 [plc5_250!4622ae44@gateway/web/freenode/ip.70.34.174.68] has parted #linuxcnc
[14:55:31] -!- AR_ has quit [Ping timeout: 248 seconds]
[14:57:09] -!- jensor [jensor!47b37591@gateway/web/freenode/ip.71.179.117.145] has joined #linuxcnc
[15:02:20] -!- kwallace [kwallace!~kwallace@smb-249.sonnet.com] has joined #linuxcnc
[15:08:20] -!- cevad has quit [Ping timeout: 248 seconds]
[15:09:12] -!- halo_cast [halo_cast!~halo_cast@p549F7F07.dip.t-dialin.net] has joined #linuxcnc
[15:10:43] -!- mhaberler has quit [Quit: mhaberler]
[15:19:16] -!- mozmck has quit [Quit: Leaving.]
[15:20:55] -!- mozmck [mozmck!~moses@client-204.235.45.161.wcfltx.partnershipbroadband.com] has joined #linuxcnc
[15:32:16] -!- joe9 has quit [Quit: leaving]
[15:33:05] -!- chopper79 has quit [Quit: Leaving.]
[15:35:22] -!- joe9 [joe9!~joe9@c-24-98-97-215.hsd1.ga.comcast.net] has joined #linuxcnc
[15:39:44] -!- joe9 has quit [Quit: leaving]
[15:45:59] -!- Dupe [Dupe!~Dupe@84-245-14-21.dsl.cambrium.nl] has joined #linuxcnc
[15:46:19] -!- joe9 [joe9!~joe9@c-24-98-97-215.hsd1.ga.comcast.net] has joined #linuxcnc
[15:48:35] -!- ktchk [ktchk!~eddie6929@n219079251194.netvigator.com] has joined #linuxcnc
[15:49:59] <r00t4rd3d> http://drillbitsunlimited.com/
[15:50:14] <r00t4rd3d> Just use the promo code SAVEME20 in the coupon field at checkout.
[15:50:19] <r00t4rd3d> %20 off
[15:52:14] <r00t4rd3d> http://drillbitsunlimited.com/Carbide-Router-Bits-You-Choose-Size-and-Qty-P3046379.aspx
[15:52:19] <r00t4rd3d> those cut really good
[15:59:10] <ktchk> Linuxcnc control mirrors deflecting laser beam to engrave, any experience?
[16:04:35] -!- adb has quit [Ping timeout: 240 seconds]
[16:10:24] -!- holgi [holgi!~chatzilla@p5B360E9A.dip0.t-ipconnect.de] has joined #linuxcnc
[16:12:26] -!- Desktop__ [Desktop__!~Dupe@84-245-14-21.dsl.cambrium.nl] has joined #linuxcnc
[16:14:25] -!- mephux has quit [Excess Flood]
[16:15:12] -!- Dupe has quit [Ping timeout: 252 seconds]
[16:16:29] -!- mhaberler [mhaberler!~mhaberler@178-191-191-147.adsl.highway.telekom.at] has joined #linuxcnc
[16:16:32] -!- tjtr33 [tjtr33!~tomp@74-93-88-241-Illinois.hfc.comcastbusiness.net] has joined #linuxcnc
[16:17:22] <jensor> Axis 2 max velocity seems limited to programmed max velocity on axis 0.
[16:17:52] -!- halo_cast has quit [Quit: Nettalk6 - www.ntalk.de]
[16:18:49] <tjtr33> ktchk: you'll have to search the archives, but there has been discussion of controlling galvos for lasers
[16:19:07] -!- chopper79 [chopper79!~Jeremy@66.94.201.202] has joined #linuxcnc
[16:20:30] <ktchk> tjtr33: thanks
[16:20:44] -!- dway has quit [Quit: dway]
[16:22:09] <TwisteR> Some tips on proper combination of kernel version & RTAI CVS revision? I want to install LinuxCNC on my gentoo notebook following that guide on the wiki.
[16:25:48] -!- DeaDTerra1 [DeaDTerra1!~DeaDTerra@226.169.216.81.static.apv.siw.siwnet.net] has joined #linuxcnc
[16:25:51] -!- DeaDTerra1 [DeaDTerra1!~DeaDTerra@226.169.216.81.static.apv.siw.siwnet.net] has parted #linuxcnc
[16:30:11] <archivist> TwisteR, notebooks/laptops are probably a complete waste of your time
[16:31:05] <archivist> they have power management that stop proper realtime, they have poor latency
[16:32:35] -!- zzolo has quit [Ping timeout: 240 seconds]
[16:33:48] -!- psha[work] has quit [Quit: leaving]
[16:34:22] <tjtr33> ktchk, a Hungarian man 'hg5bsd' created galvokins.c .
[16:34:29] <tjtr33> This kinematics corrected for some geometric error ( elliptical focus maybe ).
[16:34:32] <tjtr33> You may be able to contact him thru his youtube list.
[16:35:15] <TwisteR> archivist, even with all that power managenent stuff turned off in kernel?
[16:35:59] <TwisteR> my laptop is pretty old and has LPT
[16:36:36] <Jymmm> Even with all that APM turned off in the BIOS too.
[16:36:43] <cradek> TwisteR: before wasting lots of time, boot the linuxcnc live cd and run the latency tests
[16:37:19] <TwisteR> ok, thanks, I will try that
[16:37:19] <archivist> I am not sure I have seen a successful laptop yet in the n years I have lurked in here
[16:37:52] <cradek> I have one laptop that works fine, PIII processor, used it ca 2007 at the various emc fests
[16:38:03] <cradek> well I think I still have it somewhere...
[16:38:31] <archivist> 2007 is about when I started in here maybe
[16:38:46] * TwisteR Celeron M 1.60 GHz
[16:39:32] <archivist> veggy chip has built in power management hasnt it?
[16:40:12] <pcw_home> Speed Step
[16:42:15] -!- tjtr33 [tjtr33!~tomp@74-93-88-241-Illinois.hfc.comcastbusiness.net] has parted #linuxcnc
[16:43:31] -!- mhaberler has quit [Quit: mhaberler]
[16:46:39] <ktchk> tjtr33: I saw hg5bsd thanks
[16:46:52] <pcw_home> Oops Celeron M lacks speed step but has "Deeper Sleep"
[16:47:36] <Jymmm> You're getting sleepy, very sleepy...
[16:48:12] <jensor> Axis 2 max velocity seems limited to programmed max velocity on axis 0. What would cause this?
[16:49:17] <pcw_home> the TP will be limited by the slowest axis in a multi-axis move
[16:49:44] <ktchk> I am using a fujitsu lifebook c1321 laptop for linuxcnc. under ubuntu 10.04 emc2.51
[16:50:04] <pcw_home> (so it keeps to the programmed path)
[16:50:31] <jensor> If I do g0 z 4 it will not go at the max rate. This is a single axis move
[16:50:51] -!- chopper79 has quit [Quit: Leaving.]
[16:51:51] <pcw_home> z is axis 2?
[16:52:11] <jensor> yes
[16:52:24] <pcw_home> trivkins?
[16:52:43] <jensor> Don't know what you are asking
[16:53:49] <pcw_home> are you using some fancy kinematics?
[16:54:07] <jensor> not that i'm aware of
[16:54:29] <pcw_home> OK so no idea, I have not seen such an issue
[16:54:47] <jensor> 1BP.ini
http://pastebin.com/1svqwYMp
[16:57:04] -!- adb [adb!~IonMoldov@178.211.237.94] has joined #linuxcnc
[16:57:31] -!- tjtr33 [tjtr33!~tomp@74-93-88-241-Illinois.hfc.comcastbusiness.net] has joined #linuxcnc
[16:57:44] -!- skunkworks [skunkworks!~skunkwork@68-115-41-210.static.eucl.wi.charter.com] has joined #linuxcnc
[16:58:57] -!- adb_ [adb_!~IonMoldov@178.211.237.94] has joined #linuxcnc
[16:59:12] -!- Desktop__ has quit [Read error: Connection reset by peer]
[16:59:28] -!- adb_ has quit [Read error: Connection reset by peer]
[17:01:34] -!- tchui341 has quit [Quit: Leaving.]
[17:01:39] -!- ktchk [ktchk!~eddie6929@n219079251194.netvigator.com] has parted #linuxcnc
[17:02:01] -!- V0idExp has quit [Quit: Leaving.]
[17:09:54] -!- bedah [bedah!~bedah@f050184180.adsl.alicedsl.de] has joined #linuxcnc
[17:14:37] -!- mattions has quit [Quit: Leaving]
[17:28:37] -!- micges [micges!~micges@dfv137.neoplus.adsl.tpnet.pl] has joined #linuxcnc
[17:28:44] -!- AR_ [AR_!~AR@Dyn148234.cc.lehigh.edu] has joined #linuxcnc
[17:31:28] -!- mackerski has quit [Quit: mackerski]
[17:34:10] -!- zzolo has quit [Quit: zzolo]
[17:38:24] -!- tmcw has quit [Remote host closed the connection]
[17:42:37] -!- Maukka [Maukka!5391d1c3@gateway/web/freenode/ip.83.145.209.195] has joined #linuxcnc
[17:44:55] -!- Maukka has quit [Client Quit]
[17:49:26] -!- phantoxeD has quit [Ping timeout: 255 seconds]
[17:50:48] -!- IchGuckLive [IchGuckLive!~chatzilla@95-89-101-95-dynip.superkabel.de] has joined #linuxcnc
[17:50:53] <IchGuckLive> hi all B)
[17:52:19] -!- phantoxeD [phantoxeD!~destroy@a89-155-23-52.cpe.netcabo.pt] has joined #linuxcnc
[17:52:28] <jensor> Is there anyone here who could help resolve this problem.? Axis 2 max velocity is limited to programmed max velocity on axis 0.
[17:53:17] <IchGuckLive> in the ini the max is ?
[17:53:17] <Jymmm> jensor: pcw_home already told you.
[17:53:42] <Jymmm> jensor: you can't go higher than the lowest axis
[17:54:48] <jensor> axis 0 (x) axis is .9. Axis 1 (y) is .6. Axis 2 (Z) is 1.5
[17:55:06] <jensor> axis z will jog at 1.5
[17:55:33] <jensor> G0 z -4 moves at .9 (54ipm)
[17:56:22] <IchGuckLive> jensor: are you on 2.6 pre
[17:56:29] -!- V0idExp [V0idExp!~v0idexp@net-188-153-163-133.cust.dsl.teletu.it] has joined #linuxcnc
[17:56:46] <jensor> what do you mean 2.6 pre?
[17:56:52] <IchGuckLive> the version
[17:57:04] <jensor> I'm using Axis 2.3.5
[17:57:18] <IchGuckLive> why dont you update
[17:57:40] <IchGuckLive> http://buildbot.linuxcnc.org/
[17:58:00] <jensor> not sure how to do that - It's been a while since I configured the setup
[17:58:24] <IchGuckLive> jensor: your home language is
[17:58:31] <jensor> english
[17:58:41] <IchGuckLive> im german
[17:58:54] <IchGuckLive> are you on 10.04
[17:59:47] <jensor> What do you mean by 10.04?
[18:00:00] <Jymmm> Ubuntu 10.04
[18:00:04] <IchGuckLive> cat /etc/*release
[18:00:14] -!- AR_ has quit [Ping timeout: 255 seconds]
[18:00:15] <IchGuckLive> thype this in a terminal at the mashine pc
[18:00:20] <jensor> I'll check
[18:02:31] <IchGuckLive> @ all is the g-code manual also downloadable somewhere ? i fond nothing at the doco
[18:02:47] <jensor> It returns Ubuntu 6.06.1 LTS dapper
[18:02:48] <IchGuckLive> for a ofline mashie
[18:03:01] <IchGuckLive> jensor: this is so BAD
[18:03:14] <IchGuckLive> you realy need to do somthing
[18:03:20] -!- AR_ [AR_!~AR@Dyn148234.cc.lehigh.edu] has joined #linuxcnc
[18:03:37] <IchGuckLive> jensor: is it only a 3 axis
[18:03:47] <IchGuckLive> and only one mashine
[18:04:15] <jensor> yes a bridgeport mill
[18:04:37] <Loetmichel> IchGuckLive: why should he?
[18:04:50] <Loetmichel> never change a running machine
[18:04:51] <IchGuckLive> so save all you ngc needed and kill your PC with the latest Linuxcnc CD
[18:05:17] <IchGuckLive> Loetmichel: the interpreter is not getting this
[18:05:39] <Loetmichel> .. ok, dapper drake is six years old... COULD be goog to update, but first i would chek if the original setup works and the machine has genugh CPU and ram
[18:06:09] <jensor> Was thatba weakness that has since been cured?
[18:06:13] <Loetmichel> <- sots hins fingers
[18:06:21] <IchGuckLive> the 2.5+ will not run under dapper
[18:06:27] <Loetmichel> that is right
[18:06:56] <IchGuckLive> if he wants individuell speed he needs 2.5+
[18:07:15] <jensor> Will my ini and hal files etc still be compatible?
[18:07:22] <IchGuckLive> no
[18:07:44] <IchGuckLive> but you can print them out and get better performance by stepconf
[18:08:32] <IchGuckLive> way above 10m/min =350IPM
[18:08:54] <jensor> I never have been able to get the rti errors to zero
[18:09:08] <IchGuckLive> SMI
[18:09:10] <Tom_itx> JT-Shop-2, you gettin any weather yet?
[18:09:12] <jensor> maybe 1 or 2 every 24 hrs
[18:09:30] <IchGuckLive> it is only to you jensor
[18:09:59] <Jymmm> jensor: Are you using a laptop?
[18:10:06] <jensor> no
[18:10:19] <Jymmm> jensor: onboard video?
[18:10:52] <jensor> By the way if you were going to get another pc for this task to replace what would it be?
[18:11:08] <jensor> separate monitor
[18:11:34] <Jymmm> jensor: Not all mobo are the same, best to run the latency tests for 24+ hours from the LiveCD prior to installing
[18:11:56] <Jymmm> jensor: No are you using the onboard video, or a plugged in video card?
[18:11:56] <IchGuckLive> http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Latency-Test
[18:12:08] <IchGuckLive> jensor: here is the list
[18:12:16] <jensor> I am willing to buy another mobo if I knew what to look for
[18:12:21] <jensor> video card
[18:13:50] <jensor> tnx for the list
[18:18:51] <IchGuckLive> NP
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?LinuxCNCKnowledgeBase to your help
[18:19:54] -!- craigInnes has quit [Quit: Leaving]
[18:21:45] -!- tmcw has quit [Ping timeout: 260 seconds]
[18:22:43] -!- Cylly [Cylly!cylly@p54B13B52.dip.t-dialin.net] has joined #linuxcnc
[18:24:40] -!- wholepair [wholepair!80df2bb1@gateway/web/freenode/ip.128.223.43.177] has joined #linuxcnc
[18:25:15] <wholepair> I am having a hard time finding a manual for this:
http://www.flickr.com/photos/jeffreygarman/tags/msd021a1x/
[18:25:39] -!- Loetmichel has quit [Ping timeout: 276 seconds]
[18:25:47] <wholepair> AC servo drive - can it be interfaced/used with linuxcnc
[18:26:26] <IchGuckLive> ofcause
[18:26:39] <Jymmm> For you non coffee snobs, this is pretty good
http://www.myasianstore.com/products/126-owl-3-in-1-instant-coffee-mix.aspx Each packet makes 5oz of coffee with cream and sugar already mixed in. I've seen it locally for $3.99 for a 30ct bag.
[18:28:13] <Jymmm> I like it FAR BETTER than the Nestle one
[18:28:15] <IchGuckLive> wholepair: you got specific driver infos
[18:28:23] -!- jensor has quit [Ping timeout: 245 seconds]
[18:28:33] -!- b_b has quit [Changing host]
[18:30:39] Cylly is now known as Loetmichel
[18:30:44] <IchGuckLive> wholepair: ? Mesa 5i25 7i77
[18:31:03] <wholepair> IchGuckLive: just the sticker on the side of the enclosure - panasonic AC Servo Drive - MSD021A1X
[18:31:18] <IchGuckLive> B)
[18:32:01] <wholepair> IchGuckLive: I don't have any Mesa hardware - would it work with that?
[18:32:19] <IchGuckLive> yes
[18:32:29] <IchGuckLive> is it a plasma ?
[18:36:41] <IchGuckLive> Parameters for Position Control , Speed Control Torque Control ...... so you are fine with that
[18:38:18] -!- wholepair [wholepair!80df2bb1@gateway/web/freenode/ip.128.223.43.177] has parted #linuxcnc
[18:41:29] -!- jfire has quit [Quit: Leaving.]
[18:49:42] <mrsun_> anyone got experience with brazing/silver soldering etc? :)
[18:50:13] <IchGuckLive> i fond the docs ->
http://linuxcnc.org/docs/devel/html/gcode/
[18:51:32] <IchGuckLive> mrsun_: ask Loetmichel he is the solder master
[18:53:04] -!- hdokes [hdokes!~IceChat77@173-165-40-177-Illinois.hfc.comcastbusiness.net] has joined #linuxcnc
[18:54:53] <r00t4rd3d> I wonder how a Doodler would do on a cnc router
[18:55:30] <archivist> mrsun_, something you have to watch, not too hard but clean metal and the right flux
[18:55:53] <r00t4rd3d> mrsun_, Ive have silver solder before
[18:56:57] <mrsun_> well silver solder, very expensive .. brass "rod" for brazing quite cheap ... is there difference in how it flows etc? i guess the melting temp is alot lower on silver solder ?
[18:57:15] <mrsun_> and these flux covered rods, are they anything to have ?
[18:57:20] <archivist> spot the silver solder
http://www.collection.archivist.info/archive/DJCPD/PD/2005/2005_09_19_M_Cooper_Clock/P9091739.JPG
[18:57:22] <r00t4rd3d> you need to get it hot but not as hot as brass
[18:58:11] <mrsun_> what kind of death machine is that?!
[18:58:37] <archivist> a clock, with modifications
[18:58:40] <mrsun_> i know ive brazed in the forge before and there it seems that brass flows realy well also into cracks etc but i guess the less temp the better :P
[18:59:02] <Jymmm> mrsun_: Chrono Death Ray Machine
[18:59:11] <r00t4rd3d> what do you need to solder"
[18:59:13] <r00t4rd3d> ?
[18:59:17] <archivist> you need enough for it to flow nicely
[18:59:30] -!- Thetawaves_ [Thetawaves_!~Thetawave@7-139-42-72.gci.net] has joined #linuxcnc
[18:59:59] <mrsun_> r00t4rd3d, steel to steel
[19:00:39] <Jymmm> archivist: ar about what temp does silver solder melt? I need to braize a leak in a brass container
[19:00:46] -!- holgi has quit [Quit: ChatZilla 0.9.90 [Firefox 19.0/20130218165301]]
[19:01:00] -!- tmcw has quit [Ping timeout: 272 seconds]
[19:01:22] <Jymmm> archivist: and too many shiny things, where's the silver solder in that pic?
[19:01:25] <r00t4rd3d> ive use a normal soldering iron with it
[19:02:06] <Jymmm> it's a brass stove, so gets exposed to 1100F occasionally
[19:02:43] <archivist> the added brackets are built up on the clock
[19:02:44] <r00t4rd3d> silver solder wont work on that
[19:04:36] <mrsun_> work on what ?
[19:05:20] <Jymmm> 1240F melting point, 1355F flow point, maybe it might.
[19:06:44] <roycroft> jymmm: there are several silver solder alloys available, each with a different melting point
[19:06:51] <roycroft> that is how jewelers build up pieces
[19:07:05] <Jymmm> roycroft: So I see =)
http://lists.contesting.com/pipermail/amps/2000-January/015467.html
[19:07:13] <roycroft> they start with the high-temp solder and work their way down to the low temp solder as they build their piece
[19:08:25] * roycroft took a jewerlymaking class a few years ago, with hopes of gaining new skills that can be applied to general metalworking/machining, and was not disappointed
[19:08:52] <Jymmm> I alwas wanted to learn silversmithing
[19:09:12] <pcw_home> 1100F seems pretty hot for brass
[19:09:37] <pcw_home> at the minimum its going to anneal it
[19:09:41] <roycroft> i've soldered lots of brass with silver solder
[19:09:51] <Jymmm> roycroft: cool
[19:09:59] <Jymmm> I'll have to give it a try
[19:10:08] <Jymmm> roycroft: what did you use for flux?
[19:10:10] <roycroft> i usually use "easy" solder, which is the lowest melting point alloy
[19:10:20] <roycroft> a borax paste
[19:10:32] <Jymmm> hmmm
[19:10:57] <roycroft> from a jeweler outfitter
[19:11:19] <roycroft> i usually order from otto frei, but i sometimes get supplies from rio grande
[19:11:21] <Jymmm> oh, not just borax soap + water and make into a paste?
[19:11:29] -!- IchGuckLive has quit [Quit: ChatZilla 0.9.87 [Firefox 18.0/20130108033621]]
[19:11:29] <roycroft> that would probably work fine
[19:11:37] <roycroft> experiment with some scrap brass
[19:11:50] <Jymmm> no scrap brass available =)
[19:12:15] <pcw_home> try some cartridges...
[19:12:17] <roycroft> i'm sure you can get a small piece of brass tubing from a hardware store
[19:12:44] <Jymmm> roycroft: I could, just dont want to waste it =)
[19:13:30] <roycroft> better to waste a piece of scrap than damage your production piece
[19:14:20] <archivist> cand always solder a bit more onto the broken production
[19:14:39] <Jymmm> I doubt I could do that, it just the tinest of vapor leaks I'd like to seal up.
[19:15:02] <Jymmm> It's a a trangia burner
[19:18:43] <Jymmm> There seems to be a vapor leak where it's been crimped sealed
[19:19:12] JT-Shop-2 is now known as JT-Shop
[19:19:23] <Jymmm> hey jt
[19:19:32] <JT-Shop> Tom_itx: not yet
[19:19:40] <JT-Shop> hi jymmmmmmmmm
[19:19:48] <Jymmm> lol
[19:29:19] <cncbasher> JT-Shop: get my mail ok ?
[19:29:57] <JT-Shop> I just got back from a customer, let me check
[19:31:04] <Loetmichel> mrsun_: brass and Phosphoric copper solder are fpr high temp stuff which has to carry huge loads, silver solder is for lower temp solder joints which has to be a bit more sturdy than SnPb solder
[19:33:39] -!- wboykinm has quit [Remote host closed the connection]
[19:37:11] -!- V0idExp has quit [Ping timeout: 260 seconds]
[19:39:38] -!- tmcw has quit [Ping timeout: 272 seconds]
[19:46:19] <Tom_itx> JT-Shop, probably about 4-5" so far
[19:46:54] <Tom_itx> the bulk of it is supposed to come tonight
[19:52:49] -!- Thetawaves_ has quit [Quit: This computer has gone to sleep]
[19:52:50] -!- JT-Shop has quit [Read error: Connection reset by peer]
[19:53:18] -!- JT-Shop [JT-Shop!~John@184-63-140-99.cust.wildblue.net] has joined #linuxcnc
[19:55:18] <JT-Shop> Tom_itx: our wx is due this evening
[19:55:48] <JT-Shop> cncbasher: thanks this one shows the adjustment screws too
[19:56:10] <JT-Shop> and it makes more sense to me now what he did with the circuit board
[19:56:40] <cncbasher> yea hope it helps
[19:57:56] <JT-Shop> yes, it should help me now I can compair notes on all of them
[19:58:39] -!- mhaberler [mhaberler!~mhaberler@178-191-241-200.adsl.highway.telekom.at] has joined #linuxcnc
[20:01:35] -!- ravenlock has quit [Ping timeout: 240 seconds]
[20:04:54] -!- Wildhoney has quit [Ping timeout: 264 seconds]
[20:07:20] -!- tjb1 [tjb1!~tjb1@74.43.61.51] has joined #linuxcnc
[20:07:26] -!- Delysid has quit [Read error: Connection reset by peer]
[20:11:50] <cradek> http://www.youtube.com/watch?v=DQWyhezIze4
[20:12:38] <cradek> "uses cutting-edge, patent-pending technology"
[20:12:41] * cradek makes a gesture
[20:12:44] -!- tmcw has quit [Remote host closed the connection]
[20:13:07] * DJ9DJ cant breath any more
[20:13:32] <DJ9DJ> you are on the dark side! ;)
[20:23:51] -!- odogono has quit [Read error: Connection reset by peer]
[20:25:36] -!- sliptonic [sliptonic!~sliptonic@li208-58.members.linode.com] has parted #linuxcnc
[20:28:26] -!- nOStahl has quit [Quit: nOStahl]
[20:30:11] -!- bedah has quit [Quit: Ex-Chat]
[20:31:57] -!- V0idExp [V0idExp!~v0idexp@net-188-153-163-133.cust.dsl.teletu.it] has joined #linuxcnc
[20:37:05] -!- nOStahl has quit [Client Quit]
[20:39:12] -!- racycle has quit [Quit: racycle]
[20:48:13] -!- FinboySlick has quit [Quit: Leaving.]
[20:52:39] <r00t4rd3d> http://www.liveleak.com/view?i=266_1361381024
[20:53:50] <tjb1> r00t4rd3d:
[20:56:33] -!- p2800 [p2800!~chatzilla@pD9F9EB46.dip.t-dialin.net] has joined #linuxcnc
[20:58:47] <mrsun_> Loetmichel, hmm ok ... but ag 2, cu 91.8 p 6.2, that would be a phosphoric copper solder ... very cheap compared to ordenary silver solder .. is that good for soldering steel also ?
[20:59:28] <mrsun_> but has a tensil strenght of 250Nm compared to the silver solders 450 - 500Nm
[20:59:34] <mrsun_> according to the package
[21:00:23] p2800 is now known as p2800-de
[21:01:00] -!- AR_ has quit [Ping timeout: 276 seconds]
[21:01:34] -!- skunkworks has quit [Quit: Leaving]
[21:02:04] -!- V0idExp has quit [Ping timeout: 240 seconds]
[21:06:23] <mrsun_> "not recommended for brazing steel"
[21:06:32] <mrsun_> or other ferrous materials
[21:06:33] <mrsun_> hmm
[21:07:44] -!- p2800-de has quit [Quit: ChatZilla 0.9.90 [Firefox 18.0.2/20130201233328]]
[21:11:21] -!- vladimirek has quit [Remote host closed the connection]
[21:19:06] <mrsun_> so to make it easy on you, i need to solder steel to steel, where one part is galvanized but the galvanized part will be turned down in the lathe, dont know if the zink penetrates the metal but i guess not? is there a problem to solder things that are galvanized? :) so what type of solder should i use for this application =)
[21:19:36] <Loetmichel> mrsun_: with the right flux: yes
[21:19:58] <Loetmichel> wothout Flux: no chance
[21:20:17] <cradek> usually attachments of steel to steel are done by welding...?
[21:20:29] <mrsun_> but says on a page i find that phosphorous alloys are not good with steel cause it makes brittle joints
[21:20:32] <Loetmichel> depends: silver solder is possible on zinc
[21:20:47] <Loetmichel> SnPb solder also
[21:21:22] <Loetmichel> but the phosporic copper solder isnt, the zinc will burn off before the solder gets liquid
[21:21:41] <Loetmichel> mrsun_: it does
[21:22:00] <Loetmichel> it makes the STEEL britte to a certain degree as far as i remember
[21:22:11] <mrsun_> Loetmichel, i do not care about if the zink is still intact in this application tho =)
[21:22:32] <Loetmichel> is that a high load soldering?
[21:22:44] <Loetmichel> what is the pourpose?
[21:22:50] <mrsun_> Loetmichel, not realy as things will be threaded before soldering also :P
[21:23:02] <mrsun_> Loetmichel, tilting machine feet .. not a very heavy machine either :P
[21:23:16] <Loetmichel> so its just to prevent the nut from turning on the thread?
[21:23:30] <mrsun_> kinda, but i like it when stuff hold together :P
[21:23:38] <mrsun_> there will be a ball attached to the end of the threaded rod also
[21:23:56] <mrsun_> and thats the part i want soldered insted of welded
[21:24:06] <Loetmichel> use silver solder in sparse amounts and flux generously
[21:24:06] <mrsun_> ofc i could weld it then turn the weld down :P
[21:24:35] <Loetmichel> i would screw the ball on
[21:24:44] <mrsun_> Loetmichel, yes but they all say silver solder ... even the ag-cu-p solder ... then there are different ones but they cost like 10x what this rod does :P
[21:24:57] <mrsun_> Loetmichel, yeah thats what i was thinking, then solder it to make a solid joint :P
[21:25:00] <Loetmichel> drill a hole in the ball, thread it and screw it on top of the foot
[21:25:17] <mrsun_> i dont want the ball to unscrew when adjusting =)
[21:26:28] <mrsun_> and i find it a good opertunity to learn how silver solder etc works =9
[21:26:29] <mrsun_> =)
[21:26:42] <Loetmichel> mrsun_: "silver solder" is something like this:
http://shop.handwerkstadt-louis.de/artikel.php?artnr=4006062245102
[21:27:08] <Loetmichel> mrsun_: thats what green loctite is for ;-)
[21:27:18] <mrsun_> haha :P
[21:27:37] <mrsun_> loctite coasts like 5x what the highest grade brazing rod they have in town does
[21:28:15] <Loetmichel> mrsun_: but it is used a LOT less per joint, AND is undoable ;-)
[21:28:49] <mrsun_> and then you forget to put the cap on the bottle or soemthing
[21:28:52] <mrsun_> :P
[21:29:13] <Loetmichel> and you are not pressed to buy loctite, there is plenty of cheap "screw lock" on the market
[21:29:29] <Loetmichel> the cap wont hurt
[21:29:55] <Loetmichel> the screw locs harden with absence of air and presence of humidity and metal ions
[21:30:11] <Loetmichel> the stay liquid in the bottle more or less indefinetly
[21:30:51] <mrsun_> still good to learn to braze!
[21:30:55] <mrsun_> or solder or whatever =)
[21:31:03] <mrsun_> as it has alot more applications then just screw locking :P
[21:31:17] <Loetmichel> that is true
[21:32:22] <mrsun_> and in 99 out of 100 cases i always start in the wrong end, hardest first then go back to easier and easier ways :P
[21:38:17] <mrsun_> but a higher silver content solder without phosphor would be a better choice for steel to steel then ? :)
[21:38:47] -!- V0idExp [V0idExp!~v0idexp@net-188-153-163-133.cust.dsl.teletu.it] has joined #linuxcnc
[21:47:04] -!- ravenlock [ravenlock!~ravenlock@enlightenment/developer/ravenlock] has joined #linuxcnc
[21:50:03] <mrsun_> hmm i wonder if the south bend clones in sweden have the same kind of gear system as the south bends
[21:50:23] -!- mhaberler has quit [Quit: mhaberler]
[21:59:31] -!- jpk has quit [Ping timeout: 248 seconds]
[22:03:37] -!- Nick001-Shop [Nick001-Shop!~chatzilla@wlk-barre-208-103-141-188.dynamic-dialup.coretel.net] has joined #linuxcnc
[22:05:53] -!- FinboySlick [FinboySlick!~shark@squal.net] has joined #linuxcnc
[22:07:24] -!- micges has quit [Quit: Leaving]
[22:11:27] -!- odogono has quit [Quit: odogono]
[22:13:50] -!- Valen [Valen!~Valen@c211-30-129-65.blktn6.nsw.optusnet.com.au] has joined #linuxcnc
[22:20:58] -!- V0idExp has quit [Quit: Leaving.]
[22:23:54] <Connor> On MESA I/O. If I want to switch a 24v relay. Do I source 24v to the relay and mesa sync ground, or ground the relay and the MESA provides 24v supply ?
[22:24:13] -!- jacobroufa has quit [Ping timeout: 245 seconds]
[22:24:14] <Connor> I want to add a manual over switch to it too..
[22:25:39] -!- chopper79 [chopper79!~Jeremy@66.94.201.202] has joined #linuxcnc
[22:25:46] -!- pikeaero [pikeaero!~quassel@216-167-252-197.eastlink.ca] has joined #linuxcnc
[22:31:06] -!- skunkworks [skunkworks!~chatzilla@str-broadband-ccmts-ws-26.dsl.airstreamcomm.net] has joined #linuxcnc
[22:31:23] <Connor> skunkworks: Hey. Question on MESA.
[22:31:49] <skunkworks> Connor: yes?
[22:31:53] <Connor> I want to switch on/off a relay using a field I/O. but, I also want a external button to do it..
[22:32:01] <Connor> what's the best way to wire it.
[22:32:36] <Connor> I know that the MESA card will source the 24v. can it handle a back current ? I.E. if the switch were to also source 24v to the relay..
[22:33:05] <Connor> I.E. External Switch and MESA in parallel so to speak ?
[22:33:26] -!- L33TG33KG34R has quit [Ping timeout: 252 seconds]
[22:34:09] -!- L33TG33KG34R [L33TG33KG34R!~L33TG33KG@S010674ea3aa162f7.cg.shawcable.net] has joined #linuxcnc
[22:34:20] <skunkworks> Connor: that would be a question for peter
[22:35:03] <skunkworks> I have only used the mesa with opto22 interface modules
[22:36:10] <Connor> The output driver chips used on the 7I77 have built in Zener diode clamps to clamp
[22:36:10] <Connor> inductive turn-off (fly-back) spikes. This means that flyback diodes are not normally
[22:36:10] <Connor> required on inductive loads. If high current inductive loads are switched at high
[22:36:10] <Connor> frequencies, they should have flyback diodes to limit power dissipation the in 7I77's driver
[22:36:10] <Connor> chips
[22:36:42] <Connor> Not sure that'll protect the output side from 24v input...
[22:38:03] <skunkworks> sounds to me like 24v relay should be fine
[22:38:30] <skunkworks> (I concider a relay as a small inductive load) ;)
[22:38:41] <Connor> that's not the issue. I'm just thinking if I put a switch on to by-pass the MESA card to supply 24v to the coil, it's going to send 24v to the output side of the MESA card..
[22:39:09] <Connor> so, a diode may be needed.
[22:39:27] <Connor> unless that Zener diode will protect it from more than just spikes..
[22:40:25] <skunkworks> I don't think I understand what you mean
[22:41:37] <DJ9DJ> gn8
[22:41:54] <tjtr33> Connor, read pcw's conversation here
http://tom-itx.dyndns.org:81/~tom-itx/irc/logs/%23linuxcnc/2012-03-18.html especially the ssr drive stuff
[22:42:50] -!- DJ9DJ has quit [Quit: bye]
[22:48:16] -!- zlog has quit [Remote host closed the connection]
[22:48:19] -!- Tom_itx has quit []
[22:48:49] -!- skorasaurus has quit [Quit: left the building.]
[22:50:28] -!- Tom_itx [Tom_itx!~Tl@unaffiliated/toml/x-013812] has joined #linuxcnc
[22:50:38] -!- zlog [zlog!~zlog@ip68-102-206-36.ks.ok.cox.net] has joined #linuxcnc
[23:03:26] -!- hdokes has quit [Ping timeout: 252 seconds]
[23:17:33] -!- r0ute has quit [Ping timeout: 245 seconds]
[23:20:49] -!- r0ute_ has quit [Client Quit]
[23:35:44] -!- servos4ever has quit [Quit: ChatZilla 0.9.85 [SeaMonkey 2.0.11/20101206162726]]
[23:43:15] -!- sumpfralle [sumpfralle!~lars@c.mail.systemausfall.org] has joined #linuxcnc
[23:45:30] -!- tmcw has quit [Remote host closed the connection]
[23:46:56] -!- chopper79 has quit [Quit: Leaving.]
[23:47:41] -!- gumis [gumis!~gumis@dfv137.neoplus.adsl.tpnet.pl] has joined #linuxcnc
[23:48:05] gumis is now known as micges
[23:50:33] -!- sumpfralle1 [sumpfralle1!~lars@c.mail.systemausfall.org] has joined #linuxcnc
[23:51:36] -!- ve7it [ve7it!~LawrenceG@S01060014d19d0b68.pk.shawcable.net] has joined #linuxcnc
[23:52:42] <Connor> tjtr33: Not sure that's relevant..
[23:52:54] -!- sumpfralle has quit [Ping timeout: 276 seconds]
[23:53:43] -!- micges has quit [Quit: Wychodzi]
[23:55:57] -!- [1]DaveB has quit [Remote host closed the connection]
[23:58:32] -!- Keknom [Keknom!~monkeky@c-76-125-214-194.hsd1.pa.comcast.net] has joined #linuxcnc
