Back
[00:35:28] -!- andypugh has quit [Quit: andypugh]
[00:45:36] -!- zeeshan [zeeshan!~kvirc64@CPE84948c379051-CM84948c379050.cpe.net.cable.rogers.com] has joined #linuxcnc-devel
[00:55:37] -!- amnesic_away has quit [Ping timeout: 260 seconds]
[01:22:22] -!- kalxas has quit [Quit: Goodbye]
[01:31:44] -!- kingarmadillo has quit [Ping timeout: 260 seconds]
[02:15:35] <cradek> andypugh: it doesn't mean anything to me, sorry
[02:15:49] <cradek> (I hope I didn't give the impression that I know anything about that)
[03:32:05] -!- kingarmadillo has quit [Ping timeout: 246 seconds]
[03:37:18] -!- zeeshan has quit [Quit: KVIrc 4.3.1 Aria http://www.kvirc.net/ - 64bit Windows version by http://kvirc.d00p.de/]
[03:58:54] -!- Roguish has quit [Quit: ChatZilla 0.9.92-rdmsoft [XULRunner 35.0.1/20150122214805]]
[04:50:23] -!- pragmaticus has quit [Remote host closed the connection]
[05:18:04] -!- Connor has quit [Ping timeout: 260 seconds]
[05:18:45] -!- Connor [Connor!~Connor@71.203.255.220] has joined #linuxcnc-devel
[05:33:25] -!- kingarmadillo has quit [Ping timeout: 248 seconds]
[06:50:05] -!- kwallace_ofcb [kwallace_ofcb!~kwallace@162.222.30.253] has parted #linuxcnc-devel
[06:53:49] -!- ve7it has quit [Remote host closed the connection]
[07:34:20] -!- kingarmadillo has quit [Ping timeout: 260 seconds]
[09:34:43] -!- kingarmadillo has quit [Ping timeout: 252 seconds]
[09:43:58] -!- logger[psha] [logger[psha]!~loggerpsh@195.135.238.205] has joined #linuxcnc-devel
[09:51:02] -!- kingarmadillo has quit [Ping timeout: 258 seconds]
[11:03:47] -!- KimK has quit [Ping timeout: 250 seconds]
[11:16:53] -!- KimK [KimK!~Kim__@2600:8803:7a85:6d00:19a6:fdf2:2e99:7f69] has joined #linuxcnc-devel
[11:52:58] -!- KimK has quit [Ping timeout: 245 seconds]
[12:04:43] -!- KimK [KimK!~Kim__@2600:8803:7a85:6d00:19a6:fdf2:2e99:7f69] has joined #linuxcnc-devel
[12:18:03] -!- b_b has quit [Changing host]
[13:09:03] -!- kalxas has quit [Quit: Goodbye]
[13:10:38] -!- mk0 [mk0!~Orr@fiztech.basnet.by] has joined #linuxcnc-devel
[13:12:57] -!- mk0 has quit [Read error: Connection reset by peer]
[13:17:28] -!- txp has quit [Quit: Leaving]
[13:25:46] -!- mk0 [mk0!~Orr@fiztech.basnet.by] has joined #linuxcnc-devel
[13:37:25] -!- mk0 has quit [Ping timeout: 260 seconds]
[13:46:31] -!- kingarmadillo has quit [Quit: leaving]
[14:57:51] -!- pcw_home has quit [Remote host closed the connection]
[15:15:18] -!- kwallace_ofcb [kwallace_ofcb!~kwallace@162.222.30.253] has joined #linuxcnc-devel
[15:56:46] -!- JT-Shop has quit [Read error: Connection reset by peer]
[15:56:54] -!- jthornton has quit [Read error: Connection reset by peer]
[16:03:11] -!- kingarmadillo has quit [Ping timeout: 244 seconds]
[16:03:13] -!- skunkworks [skunkworks!~skunkwork@68-115-41-210.static.eucl.wi.charter.com] has joined #linuxcnc-devel
[16:07:06] <skunkworks> zlog
[16:07:07] <zlog> skunkworks: Log stored at
http://tom-itx.no-ip.biz:81/~tom-itx/irc/logs/%23linuxcnc-devel/2016-11-08.html
[16:26:24] -!- b_b has quit [Remote host closed the connection]
[17:36:43] -!- md-2 has quit [Quit: Leaving...]
[18:08:08] -!- jthornton [jthornton!~john@198.45.191.246] has joined #linuxcnc-devel
[18:08:11] -!- JT-Shop [JT-Shop!~john@198.45.191.246] has joined #linuxcnc-devel
[18:27:53] -!- ve7it [ve7it!~LawrenceG@S010648f8b3c3bc3b.pk.shawcable.net] has joined #linuxcnc-devel
[18:30:00] -!- andypugh [andypugh!~andypugh@cpc14-basl11-2-0-cust1010.20-1.cable.virginm.net] has joined #linuxcnc-devel
[19:04:09] -!- persina has quit [Quit: Page closed]
[19:12:56] -!- skunkworks_ [skunkworks_!~skunkwork@68-115-41-210.static.eucl.wi.charter.com] has joined #linuxcnc-devel
[19:15:17] -!- skunkworks has quit [Ping timeout: 240 seconds]
[19:38:54] -!- terkaa [terkaa!~terkaa@a91-155-72-157.elisa-laajakaista.fi] has joined #linuxcnc-devel
[19:39:01] <terkaa> hi
[20:07:03] -!- kingarmadillo has quit [Ping timeout: 258 seconds]
[20:18:45] -!- skunkworks_ has quit [Read error: Connection reset by peer]
[20:21:37] -!- terkaa has quit [Remote host closed the connection]
[21:16:43] <andypugh> cradek:
[21:16:51] <andypugh> Ye awake?
[21:18:53] <andypugh> There is something slightly puzzing afoot with Touchy touchy-off
[21:18:55] <andypugh> https://imagebin.ca/v/31JSrsK5xwUY
[21:19:19] <andypugh> Just wondering if you had any ideas/
[21:24:34] <andypugh> Oh, wait, it’s all my fault. Not sure how or why, but turning off the embedded tab changes the behaviour.
[21:25:42] -!- tchaddad has quit [Remote host closed the connection]
[21:27:39] <andypugh> And, just to really confuse me, putting the embedded tab back in doesn’t bring the problem back.
[21:27:48] <andypugh> Huh?
[21:36:46] <cradek> you poked set tool and X and Z are missing?
[21:36:58] <andypugh> Yes
[21:37:11] <cradek> ummmm
[21:37:51] <andypugh> It was cold in the workshop so I came in to see if it was the same on the VM. It was. So I removed my embedded tab, and the problem went away. So I put the embedded tab back, and the problem syated away.
[21:38:06] <cradek> words = words[:i] + self.axes + words[i+1:]
[21:38:14] <cradek> self.axes must be unset or wrong?
[21:38:31] <cradek> but you have XZ buttons...
[21:38:35] <cradek> I got nothin
[21:39:54] <andypugh> Nothing where?
[21:40:05] <cradek> I mean I have no guesses
[21:41:21] <andypugh> OK, just wondering if you had seen it before
[21:42:28] <andypugh> Another quirk to work around, Touchy seems to run the postgui hal file before embedding GladeVCP tabs, so if the tabs have HAL pins, it doesn’t work (with 2.7.4, I should point out)
[21:43:48] -!- tchaddad has quit [Remote host closed the connection]
[21:44:42] <cradek> hm yeah, maybe that's in the wrong place
[21:45:19] <cradek> running touchy.hal/postgui.hal is in __main__ but tab embedding is in the idle loop after other one-time setup
[21:45:26] <jepler> It looks like set_dynamic_tabs just forks off the tab-creating code with subprocess.Popen and has no way of waiting for them to be "Ready"
[21:46:08] <mozmck> I use Gscreen, but had the same problem.
[21:46:31] <mozmck> You can pass a hal file in the EMBED_TAB_COMMAND
[21:46:52] <mozmck> EMBED_TAB_COMMAND = gladevcp -x {XID} -u thc_box.py -H thc_box.tcl thc_box.glade
[21:46:53] <cradek> seems like a tricky trouble spot
[21:47:27] <mozmck> That's how I've been doing it and it works fine.
[21:48:37] <jepler> it feels like someone invested in making embedded tabs work better does need to dig in and find proper solutions for these problems.
[21:48:51] <jepler> I fear that, despite X having support for this kind of embedding, we are missing some glue that makes it work well for linuxcnc / hal apps
[21:49:11] <andypugh> I have code to polish up and document that has Touchy send a signal to the embedded tabs to say “your visible”
[21:49:24] <jepler> too bad you have to become an expert at X Window System programming just at the dusk of X.
[21:52:27] <andypugh> mozmck: What happens in yout thc_box.tcl HAL file?
[21:54:26] <mozmck> andypugh: I connect pins from the thc_box gladevcp object. It is tcl because I wanted to have more error checking (which I still need to do).
[21:55:25] <andypugh> Ah, OK! I assumed it was doing a wait. But that gets called by the embedder? Perfect :-)
[21:55:58] <mozmck> Yes, it calls the hal file after the component is ready - similar to the postgui hal
[21:57:18] <mozmck> andypugh:
http://linuxcnc.org/docs/2.7/html/gui/gladevcp.html#_integrating_into_touchy
[22:01:14] <andypugh> Yes, thanks, that works a treat
[22:01:40] <andypugh> and, cradek, the axis names came back too. <baffled>
[22:02:02] <andypugh> Now lets see if I can make something
[22:48:28] -!- BeachBumPete [BeachBumPete!~IceChat9@2601:589:8201:bbc0:3825:e1d:586b:1363] has joined #linuxcnc-devel
[22:48:47] -!- BeachBumPete [BeachBumPete!~IceChat9@2601:589:8201:bbc0:3825:e1d:586b:1363] has parted #linuxcnc-devel
[23:09:06] -!- kingarmadillo has quit [Ping timeout: 252 seconds]
[23:16:11] -!- tchaddad has quit [Remote host closed the connection]
[23:23:41] <andypugh> And yes. It all works and there was nothing (undocumented) wrong.
[23:23:53] -!- maurris has quit [Remote host closed the connection]
[23:24:01] <andypugh> And my lathe now has a spindle-nose adaptor for MT2
[23:24:28] <andypugh> (after lots of lovely sparky hard-turning)
[23:31:55] -!- Daerist has quit [Quit: Leaving]