Back
[00:00:33] <andypugh> And the output pin changes as expected too.
[00:07:45] <andypugh> And, in fact, other than the fact that the insmod error abouts the hal file load, it all works perfectly.
[00:09:20] <andypugh> micges: So, we have ethernet to 8i20 to parallel cable to 7i76 to smart-serial to 7i73 to a ribbon cable to an LCD display, all seeming to work.
[00:09:34] <andypugh> Sorry, not 8i20. 7i*0
[00:09:42] <andypugh> 7i80 eve
[00:09:44] <andypugh> n
[00:09:50] <andypugh> (Bed time!)
[00:10:31] <micges> andypugh: that's great, thnaks for test
[00:10:54] <micges> if you can leave it running with sserial for few hours
[00:11:13] <andypugh> An 8i20 would be a good test, it would indicate if the timing was OK, with hall signals heading one way, and motor control the other.
[00:11:40] <andypugh> I just need to plug it all back together and we can try that with the washing machine motor.
[00:13:26] <micges> first Peter needs to backport 7i80 eth interface to 8i20
[00:13:52] <andypugh> No, 8i20 is smart-serial
[00:14:10] <andypugh> I was meaning 7i80 to 7i76 to 8i20 to motor
[00:14:19] <micges> ah
[00:14:31] <micges> I messed up, here it's also bed time :)
[00:15:00] <andypugh> 7i80 to 7i44 to 8 x 8i20 would be a fun setup :-)
[00:15:18] <andypugh> (7i74, I suppose, with the 7i80db)
[00:16:46] <micges> seems like utimate test
[00:18:28] -!- ler_hydra has quit [Remote host closed the connection]
[00:27:17] -!- awallin_ has quit [Quit: No Ping reply in 180 seconds.]
[00:27:39] -!- awallin [awallin!awallin@lakka.kapsi.fi] has joined #linuxcnc-devel
[00:28:21] -!- sheppard has quit [Ping timeout: 248 seconds]
[00:40:48] -!- lyzidiamond has quit [Client Quit]
[00:56:17] <andypugh> Nothing like a 1kw motor and 100V to check your confidence in a system :-)
[00:57:14] <micges> :)
[00:57:30] -!- ve7it has quit [Remote host closed the connection]
[00:57:58] <micges> I'm not so confident, my first test will be 75W dc motor
[00:58:33] <micges> 7i80 + 7i40
[01:01:28] <andypugh> Right, I am going to set the system running overnight to see how it goes.
[01:01:51] <micges> thanks
[01:01:54] <micges> good night
[01:02:13] -!- andypugh has quit [Quit: andypugh]
[01:02:16] -!- micges has quit [Quit: Leaving]
[01:06:14] -!- ink has quit [Ping timeout: 240 seconds]
[01:12:59] -!- thomaslindstr_m has quit [Quit: Leaving...]
[01:15:24] <cradek> http://pastebin.com/raw.php?i=gFj18F1Q
[01:15:26] <cradek> wheeee
[01:17:38] -!- sumpfralle has quit [Client Quit]
[01:18:30] <cradek> although ...
http://pastebin.com/raw.php?i=2HpNQz4S
[01:18:51] -!- toxx has quit [Ping timeout: 246 seconds]
[01:20:07] <cradek> Generating grub.cfg ...
[01:20:07] <cradek> Found linux image: /boot/vmlinuz-3.4.55-rtai-1
[01:20:07] <cradek> Found linux image: /boot/vmlinuz-3.2.0-57-generic
[01:20:07] <cradek> Found initrd image: /boot/initrd.img-3.2.0-57-generic
[01:20:21] <cradek> and I'm not getting an initrd image for this new kernel. I wonder will it boot?
[01:21:10] <seb_kuzminsky> hi cradek
[01:22:40] <seb_kuzminsky> i also do not have an initrd for the rtai kernel, and it boots
[01:22:47] <seb_kuzminsky> that's kind of broken though :-(
[01:26:31] -!- franck34 has quit [Ping timeout: 245 seconds]
[01:30:19] <seb_kuzminsky> the deb is made with 'make-kpkg', maybe that does it wrong somehow
[01:38:44] -!- asdfasd has quit [Ping timeout: 265 seconds]
[01:38:46] -!- arkgis has quit [Remote host closed the connection]
[01:45:02] -!- Valen has quit [Read error: No route to host]
[01:56:52] -!- voxadam has quit [Quit: quit]
[01:57:21] -!- jeremy79 [jeremy79!~jeremy@173-15-98-104-Illinois.hfc.comcastbusiness.net] has joined #linuxcnc-devel
[01:58:03] -!- jeremy79 [jeremy79!~jeremy@173-15-98-104-Illinois.hfc.comcastbusiness.net] has parted #linuxcnc-devel
[02:02:01] -!- rob_h has quit [Ping timeout: 250 seconds]
[02:22:36] -!- c-bob|afk has quit [Ping timeout: 246 seconds]
[02:22:42] c-bob is now known as c-bob|afk
[02:26:38] -!- AR__ has quit [Ping timeout: 240 seconds]
[02:32:39] -!- Nekosan has quit [Quit: later folks...]
[03:05:29] -!- tinkerer has quit [Quit: Leaving.]
[03:10:54] -!- uw has quit [Quit: Leaving]
[03:11:32] -!- skorasaurus has quit [Quit: WeeChat 0.4.2]
[03:16:15] -!- cwmma has quit [Quit: cwmma]
[03:18:00] -!- jfire has quit [Ping timeout: 260 seconds]
[03:48:16] -!- AR__ has quit [Ping timeout: 265 seconds]
[03:49:34] -!- terabyte- has quit [Quit: terabyte-]
[03:57:31] -!- Tom_itx has quit [Ping timeout: 272 seconds]
[03:59:04] -!- sirdancealo2 has quit [Ping timeout: 260 seconds]
[04:01:06] -!- FinboySlick has quit [Quit: Leaving.]
[04:18:18] -!- Tom_itx [Tom_itx!~Tl@unaffiliated/toml/x-013812] has joined #linuxcnc-devel
[04:18:38] -!- jfire has quit [Ping timeout: 246 seconds]
[04:21:34] -!- Valen has quit [Quit: Leaving.]
[04:37:41] -!- dgarr has quit [Ping timeout: 252 seconds]
[04:56:07] -!- ju-emb has quit [Remote host closed the connection]
[05:09:23] -!- Nekosan has quit [Quit: later folks...]
[05:30:48] -!- tinkerer [tinkerer!~tinkerer@mail.play-pla.net] has joined #linuxcnc-devel
[06:02:05] -!- Fox_Muldr has quit [Ping timeout: 250 seconds]
[06:16:20] -!- FreezingCold has quit [Read error: Operation timed out]
[06:26:34] -!- FreezingCold has quit [Excess Flood]
[06:31:03] -!- sodamodo has quit [Ping timeout: 246 seconds]
[06:31:21] -!- arkgis has quit [Remote host closed the connection]
[06:31:45] -!- terabyte- has quit [Quit: terabyte-]
[06:51:29] -!- psha [psha!~psha@213.208.162.67] has joined #linuxcnc-devel
[06:51:55] -!- The_Ball has quit [Ping timeout: 250 seconds]
[06:55:56] -!- kwallace2 [kwallace2!~kwallace@smb-10.sonnet.com] has joined #linuxcnc-devel
[06:58:04] -!- kwallace has quit [Ping timeout: 264 seconds]
[06:59:12] -!- oeon has quit [Quit: Leaving...]
[07:02:00] -!- steves_logging has quit [Ping timeout: 260 seconds]
[07:03:02] -!- kwallace1 [kwallace1!~kwallace@smb-219.sonnet.com] has joined #linuxcnc-devel
[07:05:28] -!- kwallace2 has quit [Ping timeout: 265 seconds]
[07:20:45] -!- jfire has quit [Ping timeout: 252 seconds]
[07:41:09] -!- kwallace1 [kwallace1!~kwallace@smb-219.sonnet.com] has parted #linuxcnc-devel
[07:56:06] -!- Lathe_newbie| has quit [Ping timeout: 246 seconds]
[07:59:16] -!- FreezingCold has quit [Ping timeout: 264 seconds]
[08:19:54] -!- JT-Shop has quit [Ping timeout: 246 seconds]
[08:20:24] -!- jthornton has quit [Ping timeout: 260 seconds]
[08:20:51] -!- tjb1 has quit [Read error: Connection reset by peer]
[08:22:19] -!- jfire has quit [Ping timeout: 265 seconds]
[08:25:16] -!- Blorb has quit [Ping timeout: 245 seconds]
[08:35:05] -!- jeremy79 has quit [Quit: Leaving.]
[08:47:57] -!- phillc54 [phillc54!~phillc54@184.73-67-202.dynamic.dsl.syd.iprimus.net.au] has joined #linuxcnc-devel
[08:57:17] -!- vladimirek [vladimirek!~vladimire@95.105.250.72] has joined #linuxcnc-devel
[09:12:37] -!- franck34 has quit [Ping timeout: 246 seconds]
[09:12:45] -!- gonzo__ has quit [Ping timeout: 250 seconds]
[09:22:56] -!- jfire has quit [Ping timeout: 260 seconds]
[09:24:37] -!- mackerski has quit [Client Quit]
[09:33:45] -!- rob_h [rob_h!~rob_h@90.203.217.151] has joined #linuxcnc-devel
[09:42:45] -!- syyl has quit [Ping timeout: 252 seconds]
[09:47:23] -!- Tecan has quit [Ping timeout: 265 seconds]
[09:50:54] -!- Meduza has quit [Ping timeout: 246 seconds]
[10:05:30] -!- jst has quit [Quit: No Ping reply in 180 seconds.]
[10:11:22] -!- lexrem [lexrem!~lexrem@193.104.110.142] has joined #linuxcnc-devel
[10:15:38] -!- lexrem has quit [Remote host closed the connection]
[10:15:39] -!- mattiasb has quit [Ping timeout: 252 seconds]
[10:23:23] -!- jfire has quit [Ping timeout: 250 seconds]
[10:23:52] -!- mattiasb_ has quit [Quit: mattiasb_]
[10:36:43] -!- yangurazov [yangurazov!~yangurazo@91.210.101.159] has joined #linuxcnc-devel
[10:41:06] -!- yangurazov has quit [Remote host closed the connection]
[10:42:57] -!- gundamlh has quit [Client Quit]
[10:43:13] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[11:06:48] -!- gimps has quit [Ping timeout: 252 seconds]
[11:14:41] -!- jthornton [jthornton!~john@75.106.20.181] has joined #linuxcnc-devel
[11:20:50] -!- Valen has quit [Quit: Leaving.]
[11:24:14] -!- jfire has quit [Ping timeout: 264 seconds]
[11:25:15] -!- skunkworks has quit [Remote host closed the connection]
[11:57:54] -!- syyl- has quit [Read error: No route to host]
[12:02:29] -!- ju-emb [ju-emb!~jgnoss@190.222.143.86] has joined #linuxcnc-devel
[12:04:08] -!- MacGalempsy_ has quit [Remote host closed the connection]
[12:13:00] -!- b_b has quit [Changing host]
[12:24:17] -!- jfire has quit [Ping timeout: 250 seconds]
[12:26:37] -!- skunkworks [skunkworks!~skunkwork@68-115-41-210.static.eucl.wi.charter.com] has joined #linuxcnc-devel
[12:26:38] -!- voxadam has quit [Ping timeout: 240 seconds]
[12:32:29] -!- Fox_Muldr has quit [Ping timeout: 246 seconds]
[12:38:53] -!- R2E4_ has quit [Read error: Connection reset by peer]
[13:05:54] -!- dgarr [dgarr!~dgarrett@71-223-136-81.phnx.qwest.net] has joined #linuxcnc-devel
[13:14:07] -!- krusty_ar_ has quit [Ping timeout: 250 seconds]
[13:18:38] -!- krusty_ar has quit [Read error: Connection reset by peer]
[13:19:09] -!- krusty_ar_ has quit [Client Quit]
[13:23:12] -!- hm2-buildmaster_ [hm2-buildmaster_!~hm2-build@174-29-31-68.hlrn.qwest.net] has joined #linuxcnc-devel
[13:23:27] -!- hm2-buildmaster has quit [Ping timeout: 246 seconds]
[13:23:29] -!- phillc54 has quit [Ping timeout: 246 seconds]
[13:23:36] -!- |1li has quit [Ping timeout: 246 seconds]
[13:23:36] -!- phantoneD has quit [Ping timeout: 246 seconds]
[13:31:38] -!- jfire has quit [Quit: Leaving.]
[13:31:51] -!- md-2 has quit [Remote host closed the connection]
[13:37:05] -!- md-2 has quit [Ping timeout: 250 seconds]
[13:43:27] -!- sodamodo has quit [Ping timeout: 264 seconds]
[13:58:40] -!- Lathe_newbie has quit [Ping timeout: 264 seconds]
[14:20:26] -!- ju-emb has quit [Remote host closed the connection]
[14:26:49] -!- psha has quit [Quit: Lost terminal]
[14:53:20] -!- jeremy79 has quit [Quit: Leaving.]
[15:01:29] -!- gambakufu has quit [*.net *.split]
[15:01:29] -!- grummund has quit [*.net *.split]
[15:14:43] -!- jfire has quit [Quit: Leaving.]
[15:36:38] -!- kwallace [kwallace!~kwallace@smb-100.sonnet.com] has joined #linuxcnc-devel
[15:39:11] <cradek> seb_kuzminsky: mine booted, but the screen blinks on and off, which the original kernel didn't (but neither one of them has correct video/resolution)
[15:40:03] <cradek> I fear a setup that doesn't use initrd, because surely at least dkms is broken
[15:42:41] <cradek> if I check the "make my MP3s work" checkbutton in the xubuntu installer, it gives me that nvidia driver
[15:44:28] <skunkworks> Really? is that the 'install 3rd party softare' check box?
[15:44:36] <skunkworks> I don't know if I have had that happen.
[15:45:36] <cradek> I don't remember exactly what it said - something about allowing closed source with unknown weird licenses in order to get your MP3s to work
[15:46:27] <cradek> can't find a picture of it
[15:46:52] <cradek> http://static.howtoforge.com/images/perfect_desktop_xubuntu_12.04/3.jpg
[15:47:08] <cradek> ah you're right, it does say third-party
[15:47:14] <cradek> the MP3 thing is right below it
[15:47:22] <skunkworks> right
[15:47:41] <skunkworks> I think I have almsot always checked that.
[15:48:11] <cradek> my particular machine worked slightly better without it (but video was still wrong and I never did fix it)
[15:48:25] <cradek> without the checkbox I got 1280x1024 and with it I got 640x480, both are wrong
[15:49:24] <cradek> the bootup screen (where they show you a graphic instead of the console messages) has not worked on either machine I tried (one is quite modern) - it just displays a few lines of blue crap that aren't synced
[15:49:58] <cradek> ubuntu just seems more and more broken to me
[15:50:52] -!- `Nerobro has quit [Ping timeout: 264 seconds]
[15:53:06] <cradek> debian 7 is nice
[15:57:13] -!- steves_logging [steves_logging!~Steve@wsip-70-168-134-18.dc.dc.cox.net] has joined #linuxcnc-devel
[15:58:37] -!- kwallace2 [kwallace2!~kwallace@smb-29.sonnet.com] has joined #linuxcnc-devel
[16:00:02] -!- kwallace has quit [Ping timeout: 265 seconds]
[16:03:04] -!- Komzzpa has quit [Ping timeout: 272 seconds]
[16:06:48] -!- mozmck has quit [Read error: Connection reset by peer]
[16:07:45] -!- mozmck [mozmck!~moses@client-67.210.159.209.dfwtx.partnershipbroadband.com] has joined #linuxcnc-devel
[16:19:22] <seb_kuzminsky> i have other friends who prefer debian over ubuntu, and some who prefer mint over ubuntu
[16:19:55] <mozmck> I just installed mint and it is nice.
[16:21:54] <mozmck> I want to stay a little more up-to-date on some programs than debian stable, but debian testing can tend to change *too* much - at least it used to.
[16:23:04] <mozmck> Anyone tried SolydXK? debian (testing I think) based but they just give you monthly "update packs". Looks interesting.
[16:23:06] -!- skorasaurus has quit [Quit: WeeChat 0.4.2]
[16:23:13] <cradek> mint is a fine successor to gnome2 but I have encountered several problems with it due to clueless packaging and/or renaming
[16:23:16] -!- patrickarlt has quit [Client Quit]
[16:23:33] <cradek> they are fighting to get it in debian and debian is telling them to clean up their packages, so I bet it will improve
[16:24:46] <mozmck> Maybe you mean MATE as a successor to gnome2?
[16:24:59] <cradek> yes mint+MATE
[16:25:02] <mozmck> I'm using Cinnamon desktop and like it pretty well.
[16:25:20] <cradek> I meant they (the mint people?) are trying to get MATE into debian
[16:25:31] <cradek> I haven't tried that one
[16:25:34] <mozmck> haven't tried MATE, but I like XFCE pretty well.
[16:25:49] <jepler> fwiw I've set up XFCE as the desktop on my last 3 systems
[16:26:05] <cradek> I think my weapon of choice is xfce now, because although it doesn't quite have the features of gnome2, it has some years on it and seems free of terrible ideas
[16:26:27] <mozmck> Cinnamon is mostly a little slicker looking than XFCE, but there are some nice features of the file manager that I like better than in xfce.
[16:26:55] <cradek> I totally don't care about slick looks
[16:27:23] <mozmck> yes, xfce is good. I noticed the newest version also has a search bar in the main menu, which I've found to be pretty handy in cinnamon.
[16:27:24] <cradek> I want rectangular windows with functional decorations
[16:28:31] <cradek> the default xubuntu desktop theme had one-pixel window corners that you have to grab to resize. that's unusable.
[16:28:37] <mozmck> I don't mind it looking better, but it's the functionality I'm interested in - along with the ability to change things easily.
[16:30:26] <cradek> anymore I just try to choose the distribution and desktop that's had the least harm done to it so far - and that makes me sad
[16:31:39] <mozmck> yes. I may try solydxk (XFCE version) for my next install. I really don't care if it won't run on someones cell phone - or smart watch.
[16:32:03] <memleak> gnome 2 still the default in gentoo :)
[16:32:53] <mozmck> :) I really like debian based systems, but gentoo and arch do look interesting.
[16:33:28] <memleak> i used to be an archlinux dev, i had to stop using it because it was too unstable.
[16:33:33] <mozmck> I don't want to have to spend lots of time on the system though, because I don't have that time. I need something I can be done with and using in a few hours.
[16:33:46] <jepler> mozmck: agree
[16:33:48] <mozmck> interesting. that's what I want to avoid.
[16:33:51] <memleak> as soon as a new version of anything comes out, they package it, regardless of stability.
[16:34:14] <memleak> the day gcc 4.8 comes out is the day arch makes it the default.
[16:34:14] <cradek> I had never really used basic debian before, but was surprised recently to find that it was a fine and usable system with no harm done to it
[16:35:15] <mozmck> I started with debian in about '98, and ran testing because stable was too behind (like didn't support my hardware and other things).
[16:36:57] <memleak> arch is simply too new. if you dont constantly update it, you'll either be stuck with a broken system and hundreds of package conflicts that would take hours to repair, or you'd get lucky and find a time to update and get lucky enough which will last you awhile, but the package manager wont know what to do because it hasnt been updated in a few weeks.
[16:37:40] <mozmck> Switched to ubuntu because it worked better out of the box (at the time) than debian, and was updated reasonably often while still being stable. That has changed over the last couple years now, and I'm probably on my last ubuntu now.
[16:38:08] <memleak> arch is more of a war between the world's lastest linux utilities and libraries with absolutely no concept of anything else except version numbers
[16:38:52] <cradek> ubuntu 6-8-10 were all really good systems. it's going off the rails now.
[16:38:54] <memleak> gentoo is the most stable distribution out there, at least for me
[16:39:01] <mozmck> memleak: that's kind of the problem I had with debian unstable and testing, but probably not nearly as bad.
[16:39:22] <jepler> I've been using debian testing on my laptop and it hasn't bitten me too hard yet
[16:39:31] <jepler> servers get stable. linuxcnc would get stable.
[16:39:32] -!- sudobangbang has quit [Quit: ChatZilla 0.9.90.1 [Firefox 25.0.1/20131112160018]]
[16:39:56] <mozmck> ubuntu 10 was good, 9 was not! a number of things that had worked in 8 quit in 9, and got a little better in 10.
[16:40:10] <cradek> I've only ever used the LTSes
[16:40:54] <mozmck> jepler: I didn't have too much trouble with testing. I think I had a couple of times X wouldn't start after an update, and there would be some package conflicts, but that has been a while back now.
[16:40:54] <memleak> the only bugs i hear about with debian unstable is how in the past 10 years something kept crashing 3 times
[16:41:13] <mozmck> yes, it was not bad.
[16:41:38] <memleak> im always like.. THREE TIMES? NO WAI!
[16:43:09] <mozmck> I had more than that. I would tell my wife that I had updated again, and she would always ask "now the computer won't boot?", or "what's broken now?"
[16:43:52] <mozmck> But it was not too bad. Not a single re-install but just incremental updates for about 10 years
[16:44:00] <KGB-linuxcnc> 03Jeff Epler 05dgarr/testSHARE 019df68 06linuxcnc 10src/emc/usr_intf/axis/extensions/emcmodule.cc add PREFIX and SHARE to Python linuxcnc module * 14http://git.linuxcnc.org/?p=linuxcnc.git;a=commitdiff;h=019df68
[16:44:01] <KGB-linuxcnc> 03Dewey Garrett 05dgarr/testSHARE 5746b73 06linuxcnc 10lib/python/gremlin_view.py 10lib/python/pyngcgui.py lib/python: take advantage of linuxcnc.SHARE * 14http://git.linuxcnc.org/?p=linuxcnc.git;a=commitdiff;h=5746b73
[16:44:58] <dgarr> do i need to do anything else to get a deb built (for precise) for this test branch?
[16:45:31] <cradek> nope, it'll build all of them
[16:45:44] <dgarr> great -- thanks cradek and jepler
[16:46:11] <cradek> I think it'll end up here:
http://buildbot.linuxcnc.org/dists/precise/scratch-rt/binary-i386/
[16:47:22] -!- linuxcnc-build has quit [Excess Flood]
[16:47:35] -!- linuxcnc-build [linuxcnc-build!~linuxcnc-@174-29-31-68.hlrn.qwest.net] has joined #linuxcnc-devel
[16:47:49] <cradek> oops
[16:48:25] <cradek> linuxcnc-build: watch deb-precise-rt-binary-i386
[16:48:28] <linuxcnc-build> there are no builds currently running
[16:48:44] -!- linuxcnc-build has quit [Excess Flood]
[16:48:58] -!- linuxcnc-build [linuxcnc-build!~linuxcnc-@174-29-31-68.hlrn.qwest.net] has joined #linuxcnc-devel
[16:49:05] <cradek> linuxcnc-build: sorry I keep doing that to you
[16:49:43] <jepler> I think I encountered a problem using "/" in branch names, because it's a forbidden character in package version numbers
[16:49:56] <jepler> if buildbot eventually complains then push again with a branch name like dgarr-testSHARE instead
[16:50:04] * jepler is not sure he has the details right
[16:50:09] <cradek> jepler: see
http://buildbot.linuxcnc.org/dists/precise/scratch-rt/binary-i386/
[16:50:18] <cradek> maybe he fixed it
[16:50:44] <jepler> that's good news
[16:52:05] <cradek> linuxcnc-build: watch checkin
[16:52:05] <linuxcnc-build> watching build checkin #1541 until it finishes [1h36m26s]..
[16:52:22] <cradek> guess you can't watch the ones that haven't started ye
[16:52:22] <cradek> t
[17:01:25] `Nerobro_ is now known as hef[`Nerobro]
[17:04:42] -!- gimpswork has quit [Read error: Connection reset by peer]
[17:10:37] hef[`Nerobro] is now known as `Nerobro
[17:12:54] -!- flughafen has quit [Read error: Operation timed out]
[17:12:55] ck1 is now known as flughafen
[17:14:27] <seb_kuzminsky> all branch names should build debs fine
[17:15:03] -!- Komzpa has quit [Ping timeout: 250 seconds]
[17:15:39] <cradek> yay
[17:16:31] -!- GuShH has quit [Ping timeout: 245 seconds]
[17:16:40] -!- krusty_ar has quit [Ping timeout: 264 seconds]
[17:20:15] <seb_kuzminsky> look at how scripts/get-version-from-git transforms the branch name: it replaces everything but the allowed characters with "-"
[17:20:15] -!- krusty_ar_ has quit [Ping timeout: 250 seconds]
[17:20:43] <seb_kuzminsky> for watching a builder that hasnt started, you can use notify
[17:20:48] <seb_kuzminsky> linuxcnc-build: help notify
[17:20:48] <linuxcnc-build> Usage: notify on|off|list [<EVENT>] ... - Notify me about build events. event should be one or more of: 'started', 'finished', 'failure', 'success', 'exception' or 'xToY' (where x and Y are one of success, warnings, failure, exception, but Y is capitalized)
[17:22:15] <cradek> seb_kuzminsky: every time I asked linuxcnc-build for something that was more than a few lines long (like status) it got kicked for excess flood. is there a throttle you can turn on?
[17:22:26] <cradek> ah, thanks
[17:28:08] -!- PetefromTn has quit [Remote host closed the connection]
[17:30:03] <skunkworks> 'Fixed parabolic velocity comparison using law of cosines' '
[17:30:11] <skunkworks> what does that even mean?? ;)
[17:30:51] -!- jeremy79 has quit [Quit: Leaving.]
[17:36:09] <cradek> I know what parabolas are, and I know what the law of cosines is
[17:36:14] <cradek> I know what velocity is
[17:39:41] -!- Komzzpa has quit [Ping timeout: 272 seconds]
[17:41:38] <seb_kuzminsky> 'fixed' usually means something unusual in programming though ;-)
[17:45:46] <cradek> linuxcnc-build: notify on finished deb-precise-rt-binary-i386
[17:45:46] <linuxcnc-build> try 'notify on|off <EVENT>'
[17:46:18] -!- Komzzzpa has quit [Ping timeout: 272 seconds]
[17:46:35] <linuxcnc-build> build #1536 of hardy-i386-realtime-rip is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/hardy-i386-realtime-rip/builds/1536 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[17:46:58] <skunkworks> https://github.com/robEllenberg/linuxcnc-mirror/compare/circular-blend-arc-alpha
[17:47:12] <skunkworks> :) last commit
[17:49:42] <linuxcnc-build> build #9 of package-rt-precise-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rt-precise-source/builds/9 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[17:49:53] <linuxcnc-build> build #418 of package-xenomai-precise-source is complete: Success [3build successful configuring debian] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-xenomai-precise-source/builds/418
[17:50:30] -!- mackerski has quit [Ping timeout: 252 seconds]
[17:51:48] <linuxcnc-build> build #418 of package-rtpreempt-precise-source is complete: Success [3build successful configuring debian] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rtpreempt-precise-source/builds/418
[17:53:33] <linuxcnc-build> build #1187 of package-rt-lucid-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rt-lucid-source/builds/1187 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[17:53:35] <linuxcnc-build> build #1186 of package-sim-precise-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-sim-precise-source/builds/1186 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[17:54:10] -!- franck34 has quit [Ping timeout: 245 seconds]
[17:55:19] -!- tmcw has quit [Remote host closed the connection]
[17:55:48] -!- Komzzzpa has quit [Ping timeout: 272 seconds]
[17:57:02] -!- jfire has quit [Quit: Leaving.]
[17:57:30] -!- ink has quit [Disconnected by services]
[17:58:22] <linuxcnc-build> build #1186 of package-sim-lucid-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-sim-lucid-source/builds/1186 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:00:46] <linuxcnc-build> build #1188 of package-rt-hardy-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rt-hardy-source/builds/1188 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:03:00] -!- md-2 has quit [Quit: Leaving...]
[18:03:39] <linuxcnc-build> build #1185 of package-sim-hardy-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-sim-hardy-source/builds/1185 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:07:05] -!- sudobangbang_ has quit [Ping timeout: 246 seconds]
[18:08:01] -!- gimpswork has quit [Read error: Connection reset by peer]
[18:09:23] <linuxcnc-build> build #1197 of docs is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/docs/builds/1197 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:09:27] <linuxcnc-build> build #1541 of checkin is complete: Success [3build successful] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/checkin/builds/1541
[18:11:00] <cradek> linuxcnc-build: watch deb-precise-rt-binary-i386
[18:11:00] <linuxcnc-build> watching build deb-precise-rt-binary-i386 #9 until it finishes..
[18:12:41] -!- krusty_ar has quit [Ping timeout: 250 seconds]
[18:14:38] -!- mrsun_ has quit [Ping timeout: 240 seconds]
[18:16:25] -!- Komzzzpa has quit [Ping timeout: 272 seconds]
[18:18:31] -!- thomaslindstr_m has quit [Quit: Leaving...]
[18:26:12] -!- Komzzzpa has quit [Ping timeout: 272 seconds]
[18:28:16] -!- micges [micges!~micges@ddr157.neoplus.adsl.tpnet.pl] has joined #linuxcnc-devel
[18:29:07] <linuxcnc-build> build #1174 of deb-lucid-sim-binary-i386 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-lucid-sim-binary-i386/builds/1174 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:32:31] -!- Komzpa has quit [Ping timeout: 272 seconds]
[18:32:59] <linuxcnc-build> build #1180 of deb-precise-sim-binary-i386 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-precise-sim-binary-i386/builds/1180 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:33:21] -!- andypugh [andypugh!~andy2@cpc14-basl11-2-0-cust436.20-1.cable.virginm.net] has joined #linuxcnc-devel
[18:33:28] <seb_kuzminsky> hi andypugh
[18:33:36] <andypugh> Hi
[18:35:27] <linuxcnc-build> build #1179 of deb-precise-sim-binary-amd64 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-precise-sim-binary-amd64/builds/1179 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:36:19] <linuxcnc-build> build #9 of deb-precise-rt-binary-i386 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-precise-rt-binary-i386/builds/9 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:37:37] -!- tmcw has quit [Remote host closed the connection]
[18:40:59] -!- sumpfralle has quit [Quit: Leaving.]
[18:44:25] -!- ju-emb [ju-emb!~jgnoss@190.222.143.86] has joined #linuxcnc-devel
[18:46:29] -!- sumpfralle has quit [Ping timeout: 248 seconds]
[18:47:04] <linuxcnc-build> build #1177 of deb-hardy-sim-binary-amd64 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-hardy-sim-binary-amd64/builds/1177 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:47:50] -!- Loetmichel has quit [Ping timeout: 240 seconds]
[18:49:27] <linuxcnc-build> build #1176 of deb-hardy-sim-binary-i386 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-hardy-sim-binary-i386/builds/1176 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:49:34] <linuxcnc-build> build #1179 of deb-hardy-rt-binary-i386 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-hardy-rt-binary-i386/builds/1179 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:51:17] -!- Komzpa has quit [Ping timeout: 248 seconds]
[18:54:18] <linuxcnc-build> build #1174 of deb-lucid-sim-binary-amd64 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-lucid-sim-binary-amd64/builds/1174 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:55:57] <linuxcnc-build> build #1175 of deb-lucid-rt-binary-i386 is complete: Warnings [8warnings shell_3 shell_4] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/deb-lucid-rt-binary-i386/builds/1175 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[18:58:12] -!- petruciocoi has quit [Remote host closed the connection]
[19:00:48] -!- i_tarzan has quit [Ping timeout: 246 seconds]
[19:01:21] -!- Guest431 has quit [Read error: Connection reset by peer]
[19:01:25] -!- Komzpa has quit [Ping timeout: 248 seconds]
[19:01:42] <kwallace2> Gedit doesn't highlight .ngc files very well for me. The sample on the wiki page looks nice but the .lang file there doesn't produce the same effect on my setup. Does anyone know off-hand what might be wrong?
[19:02:10] cevad is now known as Guest18236
[19:03:36] -!- hysiht has quit [Quit: Konversation terminated!]
[19:05:59] <andypugh> There is a much better .lang file at cnc-club.ru
http://cnc-club.ru/forum/viewtopic.php?f=33&t=80&p=27169
[19:10:11] -!- IchGuckLive [IchGuckLive!~chatzilla@95-89-97-51-dynip.superkabel.de] has joined #linuxcnc-devel
[19:12:44] -!- vhomitz [vhomitz!~vhomitz@8.12.28.99] has joined #linuxcnc-devel
[19:13:41] -!- franck34 has quit [Ping timeout: 248 seconds]
[19:16:21] -!- IchGuckLive has quit [Quit: ChatZilla 0.9.87 [Firefox 20.0/20130329043827]]
[19:16:51] -!- jeremy79 has quit [Quit: Leaving.]
[19:16:53] <kwallace2> andypugh: Thank you.
[19:17:44] <andypugh> I think the problem is that the underlying format for .lang files changed at some point. (though this is at bese a vague recollection)
[19:19:02] <kwallace2> I guess the wiki page is broken :(
[19:26:21] <cradek> wiki is working for me
[19:27:52] -!- Connor has quit [Read error: Connection reset by peer]
[19:36:04] -!- patrickarlt has quit [Ping timeout: 265 seconds]
[19:37:07] <cradek> dgarr: did you see your debs are done in
http://buildbot.linuxcnc.org/dists/precise/scratch-rt/binary-i386/
[19:39:56] <dgarr> yes -- the change i made worked as wanted with the deb (thanks jepler), now i would like to add the two commits to master and delete dgarr/testSHARE
[19:40:30] <dgarr> assistance/guidance appreciated
[19:40:48] <kwallace2> cradek: Sorry, I meant the Gedit wiki page is out of date and the .lang file there doesn't work anymore. I looks like MAH did some work on a .lang file but it looks like it's part of the document system, maybe.
[19:42:51] <cradek> dgarr: ok, just merge it: git checkout master; git merge dgarr/testSHARE
[19:43:28] <dgarr> done
[19:43:42] <dgarr> then push i suppose (after dry-run) ?
[19:43:59] <cradek> yep
[19:44:27] -!- patricka_ has quit [Ping timeout: 272 seconds]
[19:46:53] <dgarr> git push --dry-run origin master --> 68b13e1..5746b73 master -> master
[19:47:44] <cradek> you might try: gitk 68b13e1..5746b73
[19:47:58] <cradek> you should see your couple of commits and your merge
[19:48:34] <cradek> if so, take off the --dry-run
[19:49:43] <dgarr> ok -the 68b13e1 indicates the last commit, not one of the new commits ?
[19:50:30] <cradek> yes it's saying master moves from 68.. to 57..
[19:50:31] -!- odogono has quit [Quit: odogono]
[19:50:56] <KGB-linuxcnc> 03Dewey Garrett 05master 5746b73 06linuxcnc fast forward * 14http://git.linuxcnc.org/?p=linuxcnc.git;a=commitdiff;h=5746b73
[19:51:04] <dgarr> thanks for the help
[19:53:25] -!- geografa has quit [Quit: Computer has gone to sleep.]
[19:53:33] <dgarr> now how do i remove the dgarr/testSHARE branch from git.linuxcnc.org?
[19:56:53] <cradek> git push origin :dgarr/testSHARE
[19:57:21] -!- tmcw has quit [Ping timeout: 246 seconds]
[19:57:21] <cradek> the format is <src>:<dst> and you can push an empty src (by specifying nothing) to delete
[19:57:40] <cradek> a fact that is hidden well in man git-push
[19:58:46] <linuxcnc-build> build #621 of precise-amd64-xenomai-rip is complete: Success [3build successful configure-debian-control] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-amd64-xenomai-rip/builds/621
[19:58:50] <linuxcnc-build> build #637 of precise-x86-rtpreempt-rip is complete: Success [3build successful configure-debian-control] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-x86-rtpreempt-rip/builds/637
[19:59:38] <KGB-linuxcnc> 05dgarr/testSHARE 5746b73 06linuxcnc 04. branch deleted * 14http://git.linuxcnc.org/?p=linuxcnc.git;a=commitdiff;h=5746b73
[19:59:54] <dgarr> thanks again
[20:00:03] <cradek> you can also delete it locally if you want, with git branch -d
[20:01:13] <linuxcnc-build> build #621 of precise-amd64-rtpreempt-rip is complete: Success [3build successful configure-debian-control] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-amd64-rtpreempt-rip/builds/621
[20:01:40] <dgarr> i know about that one, now i want to add those commits from dgarr/testSHARE to dgarr/config-cleanup ?
[20:02:00] -!- patrickarlt has quit [Remote host closed the connection]
[20:02:02] <cradek> you could just merge master into dgarr/testSHARE
[20:02:08] <cradek> err
[20:02:13] <cradek> you could just merge master into dgarr/config-cleanup
[20:02:20] <cradek> git checkout dgarr/config-cleanup; git merge master
[20:02:46] <dgarr> i'll try that a little later and report
[20:03:01] <linuxcnc-build> build #647 of precise-x86-xenomai-rip is complete: Success [3build successful configure-debian-control] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-x86-xenomai-rip/builds/647
[20:06:54] -!- adb has quit [Ping timeout: 252 seconds]
[20:16:05] -!- Komzzpa has quit [Ping timeout: 248 seconds]
[20:16:46] <linuxcnc-build> build #1537 of lucid-rtai-i386-clang is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/lucid-rtai-i386-clang/builds/1537 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:22:03] <linuxcnc-build> build #1336 of precise-amd64-sim-clang is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-amd64-sim-clang/builds/1336 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:29:19] <linuxcnc-build> build #1539 of precise-i386-sim is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-i386-sim/builds/1539 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:32:06] <linuxcnc-build> build #1541 of precise-amd64-sim is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-amd64-sim/builds/1541 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:33:46] <linuxcnc-build> build #742 of precise-i386-realtime-rip is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/precise-i386-realtime-rip/builds/742 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:35:26] <linuxcnc-build> build #1540 of lucid-amd64-sim is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/lucid-amd64-sim/builds/1540 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:35:55] <linuxcnc-build> build #1538 of lucid-i386-sim is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/lucid-i386-sim/builds/1538 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:38:34] -!- sumpfralle has quit [Ping timeout: 272 seconds]
[20:38:35] <linuxcnc-build> build #1541 of lucid-i386-realtime-rip is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/lucid-i386-realtime-rip/builds/1541 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:44:34] -!- Komzzpa has quit [Remote host closed the connection]
[20:50:32] -!- Komzzpa has quit [Ping timeout: 246 seconds]
[20:50:42] <linuxcnc-build> build #1542 of hardy-amd64-sim is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/hardy-amd64-sim/builds/1542 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:51:44] <linuxcnc-build> build #1537 of hardy-i386-realtime-rip is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/hardy-i386-realtime-rip/builds/1537 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:52:43] <linuxcnc-build> build #1540 of hardy-i386-sim is complete: Warnings [8warnings compile] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/hardy-i386-sim/builds/1540 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:55:59] <linuxcnc-build> build #10 of package-rt-precise-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rt-precise-source/builds/10 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:56:39] <linuxcnc-build> build #419 of package-xenomai-precise-source is complete: Success [3build successful configuring debian] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-xenomai-precise-source/builds/419
[20:57:57] <linuxcnc-build> build #419 of package-rtpreempt-precise-source is complete: Success [3build successful configuring debian] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rtpreempt-precise-source/builds/419
[20:59:31] <linuxcnc-build> build #1187 of package-sim-precise-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-sim-precise-source/builds/1187 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[20:59:47] <linuxcnc-build> build #1188 of package-rt-lucid-source is complete: Warnings [8warnings shell] Build details are at
http://buildbot.linuxcnc.org/buildbot/builders/package-rt-lucid-source/builds/1188 blamelist: Jeff Epler <jepler@unpythonic.net>, Dewey Garrett <dgarrett@panix.com>
[21:01:26] <seb_kuzminsky> linuxcnc-build: notify list
[21:01:26] <linuxcnc-build> The following events are being notified: ['failure', 'finished']
[21:01:31] <seb_kuzminsky> linuxcnc-build: notify off finished
[21:01:31] <linuxcnc-build> The following events are being notified: ['failure']
[21:01:34] <seb_kuzminsky> hush now
[21:04:02] -!- skunkworks has quit [Quit: Leaving]
[21:04:39] <cradek> oh he does that forever?
[21:07:05] <seb_kuzminsky> notify is like watch forever
[21:12:27] -!- micges has quit [Ping timeout: 240 seconds]
[21:15:33] -!- cmorley has quit [Ping timeout: 250 seconds]
[21:18:44] -!- fatpandas has quit [Quit: leaving]
[21:25:36] -!- micges [micges!~micges@epl166.neoplus.adsl.tpnet.pl] has joined #linuxcnc-devel
[21:30:32] -!- cmorley [cmorley!~chris@S0106204e7f8c229b.no.shawcable.net] has joined #linuxcnc-devel
[21:34:47] -!- jfire has quit [Quit: Leaving.]
[21:49:08] -!- FinboySlick has quit [Quit: Leaving.]
[21:54:02] -!- phillc54 [phillc54!~phillc54@oztime.lnk.telstra.net] has joined #linuxcnc-devel
[21:54:56] -!- cpresser has quit [Quit: Lost terminal]
[21:59:49] -!- sudobangbang_ has quit [Ping timeout: 246 seconds]
[22:06:26] -!- skunkworks [skunkworks!~chatzilla@str-broadband-ccmts-ws-26.dsl.airstreamcomm.net] has joined #linuxcnc-devel
[22:10:45] -!- sumpfralle has quit [Ping timeout: 272 seconds]
[22:10:52] -!- kiw has quit [Quit: kiw]
[22:13:52] -!- Deejay has quit [Quit: bye]
[22:23:02] -!- cwmma has quit [Ping timeout: 264 seconds]
[22:24:37] -!- phillc54 has quit [Ping timeout: 248 seconds]
[22:26:14] -!- voxadam has quit [Ping timeout: 240 seconds]
[22:30:46] Cylly is now known as Loetmichel
[22:37:33] -!- motioncontrol has quit [Quit: Sto andando via]
[22:38:17] -!- Lathe_newbie| has quit [Ping timeout: 265 seconds]
[22:40:35] -!- skorasaurus has quit [Quit: WeeChat 0.4.2]
[22:43:06] -!- Valen has quit [Read error: Operation timed out]
[22:45:20] -!- JT-Shop [JT-Shop!~John@75.106.20.181] has joined #linuxcnc-devel
[22:49:53] -!- FreezingCold has quit [Ping timeout: 246 seconds]
[22:50:21] -!- chillly has quit [Quit: Leaving]
[22:51:55] -!- terabyte- has quit [Quit: terabyte-]
[23:06:35] -!- kiw has quit [Quit: kiw]
[23:15:58] -!- jeremy79 has quit [Quit: Leaving.]
[23:21:00] -!- kiw has quit [Quit: kiw]
[23:27:00] -!- tinkerer has quit [Quit: Leaving.]
[23:29:07] -!- phillc54 [phillc54!~phillc54@oztime.lnk.telstra.net] has joined #linuxcnc-devel
[23:31:56] -!- micges has quit [Quit: Leaving]
[23:38:31] -!- geografa has quit [Read error: Connection reset by peer]
[23:39:46] -!- ler_hydra has quit [Remote host closed the connection]
[23:43:03] -!- adb has quit [Ping timeout: 252 seconds]
[23:44:05] -!- patrickarlt has quit [Read error: Connection reset by peer]
[23:46:13] -!- franck34 has quit [Ping timeout: 248 seconds]
[23:55:04] -!- lyzidiamond has quit [Quit: lyzidiamond]
